One of my routers seems to be running slow, I have done a "show interface" and the interface that appears to be running the ADSL shows the following. To me, it appears that the ADSL is syncing at 8829 Kb/s but the ATM0 interface has been configured to use a maximum of 939 Kb/s (BW 939 Kbit/sec). Is that correct?
Can I change it to the maximum the interface allows?
ATM0/0/0 is up, line protocol is up Hardware is HWIC-DSLSAR (with Alcatel ADSL Module) MTU 4470 bytes, sub MTU 4470, BW 939 Kbit/sec, DLY 540 usec, reliability 255/255, txload 23/255, rxload 216/255 Encapsulation ATM, loopback not set Encapsulation(s): AAL5 AAL2, PVC mode 23 maximum active VCs, 256 VCs per VP, 1 current VCCs VC Auto Creation Disabled. VC idle disconnect time: 300 seconds Last input 00:31:25, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: Per VC Queueing 5 minute input rate 1034000 bits/sec, 175 packets/sec 5 minute output rate 85000 bits/sec, 55 packets/sec 363574 packets input, 272762690 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 164 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 132374 packets output, 26785767 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 output buffer failures, 0 output buffers swapped out
A "show dsl interface":
ATM0/0/0 Alcatel 20190 chipset information ATU-R (DS) ATU-C (US) Modem Status: Showtime (DMTDSL_SHOWTIME) DSL Mode: ITU G.992.5 (ADSL2+) Annex A ITU STD NUM: 0x03 0x2 Chip Vendor ID: 'STMI' 'IFTN' Chip Vendor Specific: 0x0000 0x8277 Chip Vendor Country: 0x0F 0xB5 Modem Vendor ID: 'CSCO' ' ' Modem Vendor Specific: 0x0000 0x0000 Modem Vendor Country: 0xB5 0x00 Serial Number Near: FOC12250RAFCISCO73993206 Serial Number Far: Chip ID: C196 (0) DFE BOM: DFE3.0 Annex A (1) Capacity Used: 100% 100% Noise Margin: -4.0 dB 9.0 dB Output Power: 9.5 dBm -4.0 dBm Attenuation: 30.0 dB 16.0 dB FEC ES Errors: 0 0 ES Errors: 1 0 SES Errors: 1 0 LOSES Errors: 1 6 UES Errors: 0 153 Defect Status: LOM None Last Fail Code: None Watchdog Counter: 0xBC Watchdog Resets: 0 Selftest Result: 0x00 Subfunction: 0x00 Interrupts: 4174 (0 spurious) PHY Access Err: 0 Activations: 1 LED Status: OFF LED On Time: 0 LED Off Time: 0 Init FW: init_AMR-3.0.014_no_bist.bin Operation FW: AMR-3.0.014.bin FW Source: embedded FW Version: 3.0.14
We are pleased to announce availability of Beta software for 16.6.3. 16.6.3 will be the second rebuild on the 16.6 release train targeted towards Catalyst 9500/9400/9300/3850/3650 switching platforms. We are looking for early feedback from custome...