Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Bronze

ADSL trains but interface is down/down

Hi All,

I'm a bit confused. I have a site with 2 ADSL links running into a 2811 router.

One of the ADSL links went down on Friday, and Will not come back up. The interface is showing as trained and the access-provider (Qwest) is seeing it trained, but the interface status on the router is down / down. I'm not too familiar with DSL troubleshooting.

Any thoughts? Bad cable? Bad card maybe? Thanks in advance.

PPBV-Vrtr#sh ip int brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 unassigned YES NVRAM administratively down down

FastEthernet0/1 unassigned YES NVRAM administratively down down

ATM0/2/0 unassigned YES NVRAM down down

ATM0/2/0.1 10.2.1.230 YES NVRAM down down

ATM0/3/0 unassigned YES NVRAM up up

ATM0/3/0.1 10.2.1.234 YES NVRAM up up

PPBV-Vrtr#sh dsl int atm0/2/0

Alcatel 20150 chipset information

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.1 (G.DMT) Annex A

ITU STD NUM: 0x01 0x1

Vendor ID: 'ALCB' 'GSPN'

Vendor Specific: 0x0000 0x0008

Vendor Country: 0x00 0xFF

Capacity Used: 22% 103%

Noise Margin: 35.0 dB 7.0 dB

Output Power: 18.0 dBm 12.0 dBm

Attenuation: 12.5 dB 8.0 dB

Defect Status: None None

Last Fail Code: None

Selftest Result: 0x00

Subfunction: 0x15

Interrupts: 281885 (0 spurious)

PHY Access Err: 0

Activations: 12

LED Status: ON

LED On Time: 100

LED Off Time: 100

Init FW: embedded

Operation FW: embedded

SW Version: 3.8131

FW Version: 0x1A04

Interleave Fast Interleave Fast

Speed (kbps): 1536 0 896 0

Cells: 4457 0 0 0

Reed-Solomon EC: 0 0 11421 0

CRC Errors: 0 0 1 0

Header Errors: 0 0 0 0

Bit Errors: 0 0

BER Valid sec: 0 0

BER Invalid sec: 0 0

interface ATM0/2/0

no ip address

no atm ilmi-keepalive

dsl operating-mode auto

!

interface ATM0/2/0.1 point-to-point

ip address 10.2.1.230 255.255.255.252

ip pim sparse-mode

pvc 0/32

vbr-rt 800 800

tx-ring-limit 4

encapsulation aal5snap

service-policy output VOICE-8

!

!

interface ATM0/3/0

no ip address

no atm ilmi-keepalive

dsl operating-mode auto

!

interface ATM0/3/0.1 point-to-point

ip address 10.2.1.234 255.255.255.252

ip pim sparse-mode

pvc 0/32

vbr-rt 800 800

tx-ring-limit 4

encapsulation aal5snap

service-policy output VOICE-8

!

148
Views
0
Helpful
0
Replies