Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ADSL virtual access 2 is up down

show ip int brief

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 x.x.192.253 YES TFTP administratively down down

FastEthernet0/1 unassigned YES TFTP administratively down down

ATM0/0/0 unassigned YES TFTP up up

ATM0/0/0.1 unassigned YES unset administratively down down

Virtual-Access1 unassigned YES unset up up

Virtual-Access2 unassigned YES unset up down

Dialer0 x.x.48.207 YES TFTP up up

Loopback0 x.x.72.88 YES TFTP up up

WES-LOS-2811-2#

interface ATM0/0/0.1 point-to-point

no ip address

shutdown

interface ATM 0/0/0

description *** DSL

no shut

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

no atm ilmi-keepalive

dsl operating-mode auto

pvc 0/38

encapsulation aal5mux ppp dialer

dialer pool-member 1

interface Dialer0

ip address x.x.x.207 255.255.255.224

crypto map SDM_CMAP_1

ip access-group INTERNET-IN in

ip virtual-reassembly

encapsulation ppp

dialer pool 1

dialer-group 1

no cdp enable

ppp authentication chap callin

ppp chap hostname xxxx@xxxx.com

ppp chap password 0 xxxx

dialer-list 1 protocol ip permit

#show int dialer0

Dialer0 is up, line protocol is up (spoofing)

Hardware is Unknown

Internet address is x.x.x.x/27

MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation PPP, loopback not set

Keepalive set (10 sec)

DTR is pulsed for 1 seconds on reset

Interface is bound to Vi2

Last input never, output never, output hang never

Last clearing of "show interface" counters 00:11:31

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/0/16 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 42 kilobits/sec

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes

0 packets output, 0 bytes

Bound to:

Virtual-Access2 is up, line protocol is down

Hardware is Virtual Access interface

MTU 1500 bytes, BW 640 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation PPP, LCP Listen

PPPoATM vaccess, cloned from Dialer0

Vaccess status 0x44

Bound to ATM0/0/0 VCD: 2, VPI: 0, VCI: 38, loopback not set

Keepalive set (10 sec)

DTR is pulsed for 5 seconds on reset

Interface is bound to Di0 (Encapsulation PPP)

Last input never, output never, output hang never

Last clearing of "show interface" counters 00:11:33

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

140 packets output, 1680 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Bronze

Re: ADSL virtual access 2 is up down

You may try whether Authentication protocols like (CHAP or PAP) configured properly between the two virtual accesses.

1 REPLY
Bronze

Re: ADSL virtual access 2 is up down

You may try whether Authentication protocols like (CHAP or PAP) configured properly between the two virtual accesses.

2156
Views
0
Helpful
1
Replies
CreatePlease to create content