Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

AIM-ATM-4T1 - installation and configuration (IMA config)

Hello all,

I'm trying to configure 4 Data T1's from AT&T. I've purchased the AIM-ATM-4T1 Bundle, in AIM 0 on the board and installed the T1 controllers in WIC 0 and 1. in config mode i cannot seem to apply the "mode atm" in the controller sub-config? i've upgraded to the appropriate image?

wanr2-60mad-4n(config)#controller T1 0/0/0

wanr2-60mad-4n(config-controller)#mode ?

cas Configure CAS (Channel Associated Signal) mode

ccs Configure CCS (Common Channel Signal) mode

------------------------------------------

wanr2-60mad-4n#sh ver

Load for five secs: 0%/0%; one minute: 0%; five minutes: 0%

Time source is NTP, 12:46:34.842 EST Fri Dec 7 2007

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(11)T, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Sat 18-Nov-06 17:16 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

wanr2-60mad-4n uptime is 1 hour, 4 minutes

System returned to ROM by reload at 11:40:46 EST Fri Dec 7 2007

System restarted at 11:42:11 EST Fri Dec 7 2007

System image file is "flash:c2800nm-adventerprisek9-mz.124-11.T.bin"

Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.

Processor board ID FHK1140F3U8

2 Gigabit Ethernet interfaces

4 Channelized T1/PRI ports

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

-----------------------------------------

wanr2-60mad-4n#sh diag

Slot 0:

C2821 Motherboard with 2GE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

Onboard VPN : v2.3.3

EEPROM contents at hardware discovery:

PCB Serial Number : FOC113748D8

Hardware Revision : 1.0

Top Assy. Part Number : 800-26921-03

Board Revision : A0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20070918

Chassis Serial Number : FHK1140F3U8

Chassis MAC Address : 001d.a106.6d88

MAC Address block size : 32

CLEI Code : COM7M00ARA

Product (FRU) Number : CISCO2821

Part Number : 73-8853-05

Version Identifier : V04

WIC Slot 0:

T1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 32419598 Part number 800-04477-03

FRU Part Number VWIC-2MFT-T1=

Test history 0x0 RMA number 00-00-00

WIC Slot 1:

T1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 32419772 Part number 800-04477-03

FRU Part Number VWIC-2MFT-T1=

Test history 0x0 RMA number 00-00-00

-----------------------------------------

while there seems to be a lot of information on this type of scenario, none specifies the 2800 series..mostly 2600 and 3600's? Anybody?

1 REPLY
New Member

Re: AIM-ATM-4T1 - installation and configuration (IMA config)

Hi,

You are purchased a bundle, which should come with 2 VWIC2 and 1 AIM-ATM (CISCO High Performance ATM Advanced Integration Module), i believe your vendor did not install AIM-ATM or the AIM-ATM module is faulty. Please check with your vendor.

Hope it help. :-)

Rgds.

Christopher

475
Views
0
Helpful
1
Replies
CreatePlease to create content