Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

AIM-ATM in combination with a VWIC-1MFT-G703in a Cisco 3745 .cards are recognized ,when connecting the E1 line of the Provider , there seems to be a missing link between the ATM module and the E1 card.line stays down.With a cisco 2600XM there's no problem.

5 REPLIES
Purple

Re: AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

Hi,

I'm afraid I don't quite understand what the issue is. Would you be able to describe this with a bit more detail..maybe some configs would help.

Paresh

New Member

Re: AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

cisco 3745 (R7000) processor (revision 2.0) with 247808K/14336K bytes of memory.

Processor board ID JHY0852K1AP

R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2, 2048KB L3 Cache

Channelized E1, Version 1.0.

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

Primary Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

1 ATM network interface(s)

1 Channelized E1/PRI port(s)

1 ATM/Voice AIM(s)

DRAM configuration is 64 bits wide with parity disabled.

151K bytes of non-volatile configuration memory.

31744K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

!

hostname 3745

!

boot-start-marker

boot-end-marker

!

logging buffered 32000 debugging

!

no network-clock-participate wic 0

network-clock-participate aim 0

!

controller E1 0/0

mode atm aim 0

!

!

interface ATM0/0

description ATM interface to COLT.

no ip address

load-interval 30

scrambling-payload

no atm ilmi-keepalive

!

interface ATM0/0.37 point-to-point

description ATM 2M

bandwidth 2000

ip address

pvc 0/40

vbr-nrt 1920 1920 1

oam-pvc manage

encapsulation aal5snap

cisco 2650XM (MPC860P) processor (revision 0x300) with 124928K/6144K bytes of memory.

Processor board ID JAE08115WV0 (2703640495)

M860 processor: part number 5, mask 2

Channelized E1, Version 1.0.

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1.

Basic Rate ISDN software, Version 1.1.

1 FastEthernet/IEEE 802.3 interface(s)

9 ISDN Basic Rate interface(s)

1 ATM network interface(s)

1 Channelized E1/PRI port(s)

1 ATM AIM(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

no service pad

service timestamps debug datetime msec localtime

service timestamps log datetime msec localtime

service password-encryption

!

hostname 2650XM

!

!

controller E1 0/0

mode atm aim 0

!

interface ATM0/0

description ATM interface site to COLT.

no ip address

load-interval 30

scrambling-payload

no atm ilmi-keepalive

!

interface ATM0/0.37 point-to-point

description ATM 2M

bandwidth 2000

ip address 10.253.32.66 255.255.255.252

pvc 0/40

vbr-nrt 1920 1920 1

oam-pvc manage

encapsulation aal5snap

!

With the 3745 , the line doesn't come up . the E1 = UP , but the ATM interface stays down.

Purple

Re: AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

Just another question.. what IOS version and feature set are you running on the 3745 ?

Paresh

New Member

Re: AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

Soft / featureset is not realy the issue , because it has been tested with the same version = IP+

Cisco Internetwork Operating System Software

IOS (tm) 3700 Software (C3745-IS-M), Version 12.3(13), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Thu 10-Feb-05 01:10 by ssearch

Image text-base: 0x60008AF4, data-base: 0x61C20000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

ROM: 3700 Software (C3745-IS-M), Version 12.3(13), RELEASE SOFTWARE (fc2)

System returned to ROM by reload

System image file is "flash:c3745-is-mz.123-13.bin"

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IK8O3S-M), Version 12.3(10a), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2004 by cisco Systems, Inc.

Compiled Fri 22-Oct-04 20:43 by kellythw

Image text-base: 0x80008098, data-base: 0x81C7B130

Purple

Re: AIM-ATM and a Vwic-1MFT-G703 module in Cisco 3745

Howdy,

According to Feature Navigator, the AIM-Voice-30 abd AIM-ATM-Voice-30 are not supported on the 12.3(13) release for the 3745. The minimum IOS required on the 3745 is 12.3(2)T.

The feature is supported on the 12.3(10a) version for the 2650XM...

Maybe you need to upgrade your IOS and try again..

Hope that helps - pls rate the post if it does.

Paresh.

232
Views
0
Helpful
5
Replies
CreatePlease login to create content