Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

Any suggestion for rate limiting or shaping device on ISP?

My friend's company which is ISP going for upgrade of their shaping devices which is currently an ISR router. They have hundred of clients mostly are leased lines and wireless. I suggested a metro ethernet switch but they want it to be centralized in the core. Any suggestion what appliance will they use?
 

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

1. UTM firewall can do that e

1. UTM firewall can do that e.g., fortigate
     -Traffic shapping is included in the bundle of the firewall 
2. Bluecoat packetshaper
    -Full blown packetshaper

3. Bluecoat ProxySG

   -much like UTM firewall with traffic shapping

 

Don't forget to rate/mark as correct :)

7 REPLIES
Silver

You can try packet-shapers,

You can try packet-shapers, NGFWs, and even just a simple cisco router 

Cisco router basic shaping:

#conf t

#access-list 1 permit 10.10.10.0 0.0.0.255
#access-list 2 permit 10.10.20.0 0.0.0.255

#interface f0/0
  #traffic-shape group 1 1024   -bps (1Mbps)
  #traffic-shape group 2 1024   -bps (1Mbps)

 

 

New Member

Thanks..They are using ISR

Thanks..

They are using ISR routers using QoS policing and rate-limit input/output command. Now, thinking of replacing ISR with an ASR router. I only notice ASR do not accept rate-limit input/output command. Any idea of command similar to rate-limit input/output command on the vlan/interface.
 

Regards,

Caren

Silver

#conf t #access-list 101

#conf t
 
#access-list 101 permit ip any 192.168.10.0 0.0.0.255 
#access-list 102 permit ip any 192.168.20.0 0.0.0.255
 
#class-map match-any VLAN10
  #match access-group 101
 
#class-map match-any VLAN20
  #match access-group 102
      
#policy-map POLICY1
  #class VLAN10
    #shape average 8000[or 8K] -Traffic Shaping(bps)
 
  #class VLAN20
    #shape average 2M 
 
  #class class-default
 
 
APPLY
#interface f0/1
  #service-policy [input/output] POLICY1
 
Silver

Oh yeah, do note that rate

Oh yeah, do note that rate limit is per interface, with shaping or policing, you can specific per subnet or IP range.

New Member

Hi,    Thank you for your

Hi,

    Thank you for your replies. By the way, do you have any experience with specific packet shapers in the market? I cannot find cisco appliance with specific shaping purpose.

 

Thanks,

Caren

Silver

1. UTM firewall can do that e

1. UTM firewall can do that e.g., fortigate
     -Traffic shapping is included in the bundle of the firewall 
2. Bluecoat packetshaper
    -Full blown packetshaper

3. Bluecoat ProxySG

   -much like UTM firewall with traffic shapping

 

Don't forget to rate/mark as correct :)

New Member

They buy bluecoat

They buy bluecoat packetshaper but the software was corrupted just before the production deployment 'stuck in boot'.

Thanks for your reply.

 

Regards,

Caren

587
Views
0
Helpful
7
Replies
CreatePlease to create content