Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

atm session timeout

hi all,

i would ask u some information about my problem. Recently i added to my network a ls1010 on top of my 7200 bras as collector for my xdsl. I noticed a strange problem on one of 7200s. Sometimes adsl goes down, cd led is still light on but it doesn't work until i don't shutdown the pvc on 7200.

I think the problem is connected to lcp timeout or something similar.

Someone can help me?

Thanks

4 REPLIES
VIP Purple

Re: atm session timeout

Hello,

could be a bug in IOS, which version are you running on your 7200 ? Can you post the configs of your 7200 and the LS1010 ?

Regards,

GP

New Member

Re: atm session timeout

7200 IOS c7200-js-mz.124-1a.bin

LS1010 IOS ls1010-wp-mz.121-26.E2.bin

7200 config

...

interface ATM1/0

no ip address

load-interval 30

class-int ppp-atm

no atm auto-configuration

no atm ilmi-keepalive

no atm address-registration

no atm ilmi-enable

range POOL-01 pvc 10/100 10/400

encapsulation aal5mux ppp Virtual-Template10

!

range POOL-02 pvc 10/401 10/800

encapsulation aal5mux ppp Virtual-Template10

!

and so on

interface Virtual-Template10

ip unnumbered Loopback10

ip tcp header-compression

no snmp trap link-status

peer default ip address pool telecommuters

ppp authentication pap

!

LS1010 config

interface ATM3/0/2

description LINK ATM1

no ip address

logging event subif-link-status

no atm ilmi-keepalive

atm pvc 10 100 interface ATM3/0/0 10 100

atm pvc 10 102 interface ATM3/0/0 10 102

atm pvc 10 103 interface ATM3/0/0 10 103

atm pvc 10 104 interface ATM3/0/0 10 104

atm pvc 10 105 interface ATM3/0/0 10 105

atm pvc 10 107 interface ATM3/0/0 10 107

and so on for every pvc

do u need other piece of configuration?

thanks

New Member

Re: atm session timeout

I posted the configuration...can somebody help me please? thanks

New Member

Re: atm session timeout

Hi,

I have a same problem

I defined a pvc range in my BRAS,sometimes users can't establish a connection until i clear pvc range and define it again.

when this problem occur my link and line protocol is up

i use a SURPASS hiX 5300 DSLAM

and my IOS is c7200-a3jk8s-mz.122-12.bin

please tell me what's the problem and why definion of pvc range again solve the problem?

here is my config :

...

vpdn-group 1

accept-dialin

protocol pppoe

virtual-template 1

!

!

call rsvp-sync

!

!

!

!

!

!

bridge irb

!

!

interface FastEthernet0/0

ip address *.*.*.* *.*.*.*

duplex full

speed 100

pppoe enable

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface ATM1/0

no ip address

scrambling cell-payload

framing crc4adm

ima-group 0

!

interface ATM1/ima0

description ----------

ip address *.*.*.33 *.*.*.*

no atm ilmi-keepalive

pvc 1/32

protocol ip *.*.*.33 broadcast

protocol ip *.*.*.34 broadcast

!

range 1 pvc 0/32 0/232

encapsulation aal5snap

protocol pppoe

!

!

interface Virtual-Template1

ip unnumbered FastEthernet0/0

no logging event link-status

peer default ip address pool S-1

ppp max-bad-auth 3

ppp authentication pap chap DSL-Users

ppp accounting DSL-Users

!

831
Views
0
Helpful
4
Replies