Thanks Reza! Actually what I did was turn off the router ,and when it booted up again, it reverted back to the default configuration. I just didn't save the running config to the boot config. However, when I started to re-config it, I just did the simple steps, and now it works - partially.
I currently have it plugged into my linksys router which is connected to my Time Warner cable box. What I want to do next is plug it into my cable box, to make it the top router. I tried this, but when I did so, I was not assigned an IP by my ISP (same as before). I tries a crossover cable as well and that did not work. In the SDM, I did a Test Connection and it said that I didn't have an IP. I checked my Linksys Router settings and it said it was simply set up for DHCP as is my Cisco router. I am a bit confused on this one. I posted my config below.
Thanks for any replies!
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname {!REMOVED FOR SECURITY!}
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 {!REMOVED FOR SECURITY!}
!
no aaa new-model
!
resource policy
!
ip subnet-zero
!
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.0.31 10.10.0.254
ip dhcp excluded-address 10.10.0.1
!
ip dhcp pool sdm-pool1
network 10.10.0.0 255.255.255.0
domain-name {!REMOVED FOR SECURITY!}
default-router 10.10.0.1
dns-server 208.67.222.222 208.67.220.220
!
ip dhcp pool sdm-pool
!
ip dhcp pool {!REMOVED FOR SECURITY!}
host 10.10.1.2 255.255.255.0
hardware-address {!REMOVED FOR SECURITY!}
client-name {!REMOVED FOR SECURITY!}
!
!
ip domain name {!REMOVED FOR SECURITY!}
!
!
voice-card 0
no dspfarm
!
!
!
!
!
!
!
!
!
!
!
!
!
crypto pki trustpoint TP-self-signed-{!REMOVED FOR SECURITY!}
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-{!REMOVED FOR SECURITY!}
revocation-check none
rsakeypair TP-self-signed-{!REMOVED FOR SECURITY!}
!
!
crypto pki certificate chain TP-self-signed-{!REMOVED FOR SECURITY!}
certificate self-signed 01
{!REMOVED FOR SECURITY!}
quit
username root privilege 15 secret 5 {!REMOVED FOR SECURITY!}
!
!
!
!
!
!
interface FastEthernet0/0
description $ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$$ETH-WAN$
ip address dhcp client-id FastEthernet0/0 hostname {!REMOVED FOR SECURITY!}
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
interface FastEthernet0/1
description $ETH-LAN$
ip address 10.10.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
!
ip classless
!
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface FastEthernet0/0 overload
!
access-list 1 remark INSIDE_IF=FastEthernet0/1
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.10.0.0 0.0.0.255
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
banner login ^C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege level of 15.
Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.
username privilege 15 secret 0
no username cisco
Replace and with the username and password you want to use.
For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
-----------------------------------------------------------------------
^C
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
!
end
