Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hey Everyone,Def need some advice on this...it just won't work!Setup is basically: LAN Switch has a direct SDWAN connection from Port 1 on the Velo with DHCP Relay enabled on the Internal Subnet Address of say 172.16.1.150 to the S2S DHCP Server on 1...
Dear community,I have a lab with 3 routers. R3,R4 and R5. R3 and R5 have bgp configuration as below. I have eigrp 100 running on all the routers and there is reachiblity to all IPs. R4 is BETWEEN R3 and R5. why can't a bgp session be formed between R...
Hi,Is line vty is require when router connect through ssh remotely. If require what will be the command for router N540x .Thanks,Prash
Hi all,I have a scenario where customer wan link is upgraded from 60 mb to 80 mb and customer is reporting performance issues now.On wan inter 80 mb QoS policy is applied , 56 for dscp ef premium class and 22 mb for standard class .I am seeing violat...
hi every one,i have an issue with EIGRP Relationship in DMVPN connections,the neighbor reset between the hub and the spokeand i got the Errors:%DUAL-5-NBRCHANGE: EIGRP-IPv4 77: Neighbor 172.19.1.36 (Tunnel191) is down: Interface PEER-TERMINATION rece...
Dear Everyone,Cisco Firepower Extensible Operating System (FX-OS) v2.12.0 (build 499)Cisco Firepower 2130 Threat Defense v7.2.4 (build 165)Model : Cisco Firepower 2130 Threat Defense (77) Version 7.2.4 (Build 165)I need help configuring an IPsec VPN ...
Hi all! As far as I know, when you configurate the command, eigrp stub, it automatically add the keyword 'connect' and 'summary' at the end of the command:When configuring the eigrp stub at work, is it generally necessary to add the summary keyword t...
Hi,Is I need to configure line vty connect on cisco n540x router remotely through ssh.If yes please provide the command. This is really help me.Thanks,Prashanth
Greetings all,I am struggling to route traffic out a layer 2 port from a layer 3 port on a Cisco 1921 Integrated Services Routers (ISR). Please help me figure out how to route traffic from my layer 3 port to layer 2 port on onboard HWIC card.Cisco 19...
Here is my setuphere is the output of `sh run` command on my router`R1#sh runBuilding configuration...Current configuration : 1313 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encrypt...
where to get answer of any error detected in logs of cisco switch & router
Hello Community,Just chasing some feedback on the setup that load balances traffic on the both WAN uplinks that are connected to 2 Starlink kits.I know its going to be ECMP using the equal cost but my question is what would be the best implementation...
Hi DMVPN Pros Maybe a DMVPN hero can help me out. I have a DMVPN setup with multiple spokes that are behind the same CGN (mobile 4G network). So there is a possibility that 2 CPEs may have the same public IP address after processing the CGN. Is this ...
Hello, I am upgrading workstations to RHEL 8, and I have 2/3 2960-s switches, and also a router (that I keep as a spare), that 'complain when I use ssh to connect to them.$ ssh admin@south.localdomainUnable to negotiate with 192.168.1.3 port 22: no ...
I'm trying to debug and only view ICMP traffic between 2 specific host via ping, but there are so many messages, it's hard to troubleshoot. Is there a way to filter and see only the ICMP traffic between them? I've tried debug ip icmp and using acl(...
