Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

BGP Prefix-list & Route-map Functionality ?

Hi All,

I am currently working on filtering static & connected route updates between two(R1 & R2) IBGP neighbours.

I have static & connected routes in R1 from which I want to send only limited routes to R2.

Satic & Connected routes in R1:

<table>

Prot Type Dest Address/Mask Next-hop Age Distance Metric Tag Interface name
---- ---- ----------------- -------- --- -------- ------ ---------- --------------
static 10.1.1.1/32 0.0.0.0 1h41m11s 0 0 0 utun
connected 10.2.1.0/24 10.2.1.1 1h41m16s 0 0 0 ueth1
local 10.2.1.1/32 0.0.0.0 1h41m16s 0 0 0 directly connected
connected 10.3.0.0/16 10.3.5.1 1h41m16s 0 0 0 ueth2
local 10.3.5.1/32 0.0.0.0 1h41m16s 0 0 0 directly connected
connected 10.10.246.0/24 10.10.246.13 1h41m16s 0 0 0 eth0
local 10.10.246.13/32 0.0.0.0 1h41m17s 0 0 0 directly connected
static 192.168.1.0/24 10.10.246.40 1h41m12s 1 1 0 eth0
static 192.168.2.0/24 10.10.246.40 1h41m12s 1 1 0 eth0
static 192.168.3.0/24 10.10.246.40 1h41m12s 1 1 0 eth0
static 192.168.4.0/24 10.10.246.40 1h41m12s 1 1 0 eth0
static 192.168.5.0/24 10.10.246.40 1h41m12s 1 1 0 eth0
static 192.168.10.0/24 10.10.246.40 1h41m12s 1 1 0 eth0

<table>

<table>

R1 configuration:

router bgp 65000
vrf global
administrative-status up
router-id 192.0.0.10

prefix-list pl-con
seq 1
permit
address-family ipv4 unicast
192.168.2.0/24
exit-address-family
!
!
!
route-map rm-con 1
permit
set-community 1:65535
set-community-action set-specific
set-local-preference 150
match-ip nlri prefix-list pl-con
!

route-policy rp1
export-route-map rm-con

neighbor 10.10.246.14 remote-as 65000
route-policy rp1

redistribute connected address-family ipv4

redistribute static address-family ipv4

<table>


With the above configuration I can see R1 advertises 192.168.2.0/24 alone to R2.

But here comes my problem, when I add new prefix-list & route-map to neighbor 10.10.246.14 then I can see all the static & connected routes advertised to it(UPDATE Messages)

<table>

prefix-list pl-con-2
seq 1
permit
address-family ipv4 unicast
192.168.10.0/24
exit-address-family
!
!
!
route-map rm-con 2
permit
set-community 1:65535
set-community-action set-specific
set-local-preference 150
match-ip nlri prefix-list pl-con-2
!

<table>

After some time R1 sends Route withdraw messages to R2 & R2 will have updates to 192.168.2.0/24 & 192.168.10.0/24.

My question is when I add new prefix-list & route-map is this the expected behaviour by R1 or R1 shall update only 192.168.2.0/24 & 192.168.10.0/24 to R2.

49
Views
0
Helpful
0
Replies
CreatePlease to create content