Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Bonding in 878

Re: bonding in 878

How can i know what is the real speed that synchronizing my bundle line with two shdsl 2M/2M? Add the output of sh controller dsl 0:

CPE251#sh controllers dsl 0

DSL 0 controller UP
Globespan xDSL controller chipset
Line Mode: Four Wire Standard
DSL mode: Trained with SHDSL Annex B
Frame mode: Utopia
Configured Line rate: 4096Kbps
Line Re-activated 1 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CPE

Line 0 statistics

        Current 15 min counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 0

        Previous 15 min counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 0

        Current 24 hr counters
                CRC : 5 LOSW Defect : 0 ES : 5  SES : 0 UAS : 32

        Previous 24 hr counters
                CRC : 5 LOSW Defect : 0 ES : 5  SES : 0 UAS : 0


Line 1 statistics

        Current 15 min counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 0

        Previous 15 min counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 0

        Current 24 hr counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 32

        Previous 24 hr counters
                CRC : 0 LOSW Defect : 0 ES : 0  SES : 0 UAS : 0

Line-0 status
Chipset Version:  0
Firmware Version:  R4.2.1
Modem Status:  Data, Status 1
Last Fail Mode:  Failed during Carrier Detect status:0x1
Line rate:  2056 Kbps
Framer Sync Status: In Sync
Rcv Clock Status: In the Range
Loop Attenuation:  13.5 dB
Transmit Power:  14.5 dB
Receiver Gain:  27.7420 dB
SNR Sampling:  37.9860 dB
Receive HEC Error Count:  0
Line-1 status
Chipset Version:  0
Firmware Version:  R4.2.1
Modem Status:  Data, Status 1
Last Fail Mode:  Failed during Carrier Detect status:0x1
Line rate:  2056 Kbps
Framer Sync Status: In Sync
Rcv Clock Status: In the Range
Loop Attenuation:  13.1 dB
Transmit Power:  14.5 dB
Receiver Gain:  27.420 dB
SNR Sampling:  38.9550 dB
Receive HEC Error Count:  0
Dying Gasp: Present

Thanks in advanced

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Bonding in 878

Yes, it's working correctly.

4 REPLIES
Hall of Fame Super Gold

Re: Bonding in 878

Line rate:  2056 Kbps

New Member

Re: Bonding in 878

Ok, but there are two lines "line rate: 2056". This means that it is working correctly (4M/4M)?

Thanks

Hall of Fame Super Gold

Re: Bonding in 878

Yes, it's working correctly.

New Member

Re: Bonding in 878

Thanks Paolo

Saludos

256
Views
0
Helpful
4
Replies