Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Booting problem with c2801

Greetings friend !

I am experiencing a booting problem in our c2801 model. After powering router on, router boots again and again without stopping.

AGAIN AND AGAIN ROUTER IS SHOWING SAME SEQUENCE FOR INFINITE TIME. Pressing break key iam able to jump to rommon, but even though after using ?confreg 0x2102,- 15 not able to configure the router to boot normally.

PLS HELP!

the actual configuration of router is below:

System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c2801 processor with 131072 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

rogram load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xd49718

Self decompressing the image : #################################################

################################################################################

######## [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0X003AA110 public buffer pools

0X00211000 public particle pools

0X0013 0X00035000 Card in slot 2

0X000021B8 Onboard USB

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Allocating additional 7692663 bytes to IO Memory.

PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes

******C2801: FPGA PCI Base Address Register MISMATCH. Bus 0, Dev 17, Wrote: 0x4 B000000, Read: 0xFFFFE000.

System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by c

00000, Read: 0xFFFFE000.

System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c2801 processor with 131072 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xd49718

Self decompressing the image : #################################################

################################################################################

####

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0X003AA110 public buffer pools

0X00211000 public particle pools

0X0013 0X00035000 Card in slot 2

0X000021B8 Onboard USB

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Allocating additional 7692663 bytes to IO Memory.

PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes

******C2801: FPGA PCI Base Address Register MISMATCH. Bus 0, Dev 17, Wrote: 0x4 B000000, Read: 0xFFFFE000.

System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2004 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c2801 processor with 131072 Kbytes of main memory

Main memory is configured to 64 bit mode

1 REPLY

Re: Booting problem with c2801

Your router is experiencing a hardware problem that is indicated by the following line:

******C2801: FPGA PCI Base Address Register MISMATCH. Bus 0, Dev 17, Wrote: 0x4 B000000, Read: 0xFFFFE000.

Best thing will be to open a TAC-case and send it in for repair.

Regards,

Leo

376
Views
0
Helpful
1
Replies
CreatePlease to create content