Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

bridging over G.SHDSL on Cisco 878 routers

Hi,

I have connected two cisco 878 back to back and can ping between routers when I assign an IP address to the dialer interface.

I am testing out bridging over the dialer interfaces and have no connectivity. Here is the relevant config. What am I missing

SITE 1

----------

controller DSL 0

mode atm

line-term cpe

line-mode 2-wire line-zero

dsl-mode shdsl symmetric annex A

line-rate auto

interface ATM0

no ip address

no atm ilmi-keepalive

pvc 8/35

encapsulation aal5mux ppp dialer

dialer pool-member 1

bridge-group 1

interface Dialer0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

encapsulation ppp

ip route-cache flow

dialer pool 1

dialer-group 1

no cdp enable

bridge-group 1

interface Vlan1

description *** Management ***

ip address 192.168.1.2 255.255.255.0

dialer-list 1 protocol ip permit

bridge 1 protocol ieee

SITE 2

------------

controller DSL 0

mode atm

line-term co

line-mode 2-wire line-zero

dsl-mode shdsl symmetric annex A

line-rate auto

interface ATM0

no ip address

no atm ilmi-keepalive

pvc 8/35

encapsulation aal5mux ppp dialer

dialer pool-member 1

bridge-group 1

interface Dialer0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

encapsulation ppp

ip route-cache flow

dialer pool 1

dialer-group 1

no cdp enable

bridge-group 1

interface Vlan1

description *** Management ***

ip address 192.168.1.1 255.255.255.0

dialer-list 1 protocol ip permit

bridge 1 protocol ieee

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: bridging over G.SHDSL on Cisco 878 routers

Hello Chris,

in this kind of config the dialer is not needed

I would do the following:

remove any reference to the dialer in the atm0 interface

change the pvc 8/35 encapsulation to

enc aal5snap

and retry probably the ppp session is not coming up and so it is disturbing.

Hope to help

Giuseppe

5 REPLIES
Hall of Fame Super Silver

Re: bridging over G.SHDSL on Cisco 878 routers

Hello Paul,

what is missing here are the lan segments that should take part in the bridge.

you can try this:

int vlan 1

no ip address

bridge-group 1

int BVI1

ip address 192.168.1.2 255.255.255.0

bridge 1 route ip

I'm not sure if this is supported on this platform but the idea of bridging is this you create a virtual lan bridge between the two lans at the two sites but each router provides two arms the lan segment and the wan segment.

However, routing is to be preferred in a production network for several reasons including performance, broadcast control and security.

Hope to help

Giuseppe

New Member

Re: bridging over G.SHDSL on Cisco 878 routers

Thanks Giuseppe,

I will try it and let you know how I make out. Routing works, but the customer is just trying to extend their LAN over Cat3.

New Member

Re: bridging over G.SHDSL on Cisco 878 routers

Hi Giuseppe,

I added those commands to my existing configs, but still cannot ping between routers.

Here is output of sh bridge group from one of the routers

SHP-CO-RTR#sh bridge group

Bridge Group 1 is running the IEEE compatible Spanning Tree protocol

Port 14 (Vlan1) of bridge group 1 is forwarding

Port 16 (ATM0 RFC 1483) of bridge group 1 is forwarding

Port 17 (Dialer0) of bridge group 1 is forwarding

From a laptop connected to one of the router, i can ping the router but not across to the other side.

Any ideas are welcome.

Chris

Hall of Fame Super Silver

Re: bridging over G.SHDSL on Cisco 878 routers

Hello Chris,

in this kind of config the dialer is not needed

I would do the following:

remove any reference to the dialer in the atm0 interface

change the pvc 8/35 encapsulation to

enc aal5snap

and retry probably the ppp session is not coming up and so it is disturbing.

Hope to help

Giuseppe

New Member

Re: bridging over G.SHDSL on Cisco 878 routers

Thanks Giuseppe,

The changes worked.

1684
Views
0
Helpful
5
Replies