Hi, I have a problem with my LDP Neighbors when an ATM interface flaps. When the Physical IF flaps, the LDP Neighbors over other IF goes down.
The show buffers show me a peak at the same time of the failiure.
# sh buffers Buffer elements: 1118 in free list (500 max allowed) 4022421 hits, 0 misses, 1119 created
Public buffer pools: Small buffers, 104 bytes (total 50, permanent 50, peak 95 @ 4d19h): 47 in free list (20 min, 150 max allowed) 10116037 hits, 49 misses, 78 trims, 78 created 3 failures (0 no memory) Middle buffers, 600 bytes (total 28, permanent 25, peak 145 @ 3w1d): 28 in free list (10 min, 150 max allowed) 2400429 hits, 250 misses, 494 trims, 497 created 51 failures (0 no memory) Big buffers, 1536 bytes (total 50, permanent 50): 50 in free list (5 min, 150 max allowed) 410966 hits, 0 misses, 0 trims, 0 created 0 failures (0 no memory) VeryBig buffers, 4520 bytes (total 11, permanent 10, peak 13 @ 4d19h): 10 in free list (0 min, 100 max allowed) 319327 hits, 2 misses, 3 trims, 4 created 0 failures (0 no memory)
: %ENTITY_ALARM-6-INFO: CLEAR CRITICAL AT2/0 Physical Port Link Down %TDP-5-INFO: ATM2/0.239118: LDP started %LINK-3-UPDOWN: Interface ATM2/0, changed state to up . %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM2/0, changed state to up %LDP-5-NBRCHG: LDP Neighbor 10.10.66.171:0 (1) is UP : %OSPF-5-ADJCHG: Process 66, Nbr 10.10.66.171 on ATM2/0.239118 from LOADING to FULL, Loading Done %LDP-5-NBRCHG: LDP Neighbor 10.10.66.129:0 (4) is DOWN (Received error notification from peer: Holddown time expired) : %LDP-5-NBRCHG: LDP Neighbor 10.10.66.50:0 (2) is DOWN (Received error notification from peer: Holddown time expired) %LDP-5-NBRCHG: LDP Neighbor 10.10.66.230:0 (3) is DOWN (Received error notification from peer: Holddown time expired) %LDP-5-NBRCHG: LDP Neighbor 10.10.66.50:0 (5) is UP %LDP-5-NBRCHG: LDP Neighbor 10.10.66.230:0 (6) is UP . %LDP-5-NBRCHG: LDP Neighbor 10.10.66.129:0 (2) is UP
Question We run asr9001 with XR 6.1.3, and we have a very long delay to
login w/ SSH 1 or 2 to the device compare to IOS device. After
investigation, the there is 1s delay between the client KEXDH_INIT and
the server (XR) KEXDH_REPLY. After debug ssh serv...
Introduction The purpose of this document is to demonstrate the Open
Shortest Path First (OSPF) behavior when the V-bit (Virtual-link bit) is
present in a non-backbone area. The V-bit is signaled in Type-1 LSA only
if the router is the endpoint of one or ...
Hi, I am seeing quite a few issues with patch install and wanted to
share my experience and workaround to this. Login to admin via CLI, then
access root with the “shell” command Issue “df –h” and you’ll probably
see the following directory full or nearly ...