Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Can't browse certaing sites through dialer interface

Hi all. For the past 30 days my users cannot browse to a short list of sites.

The only oddity is that they use a dialer to route the traffic through.

Attached is the config.

The issue started 30 days ago with bellcanada.net.

We have tried using the bellcanada.net DNS with no change in behavior.

Any ideas?

12 REPLIES
Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

Hi,

please configure under dialer1:

ip tcp adjust-mss 1452.

Hope this helps, please rate post if it does!

New Member

Re: Can't browse certaing sites through dialer interface

This made no difference.

Any other ideas?

Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

My bad, per cisco doc the command goes under the "ip nat inside" interface:

http://cisco.com/en/US/docs/ios/12_2t/12_2t4/feature/guide/ft_admss.html

Please let us know if it solves your issue.

New Member

Re: Can't browse certaing sites through dialer interface

I'm using 12.3(XT2) with a cisco 1750 router.

Can I just set MTU to 1452?

Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

The IOS that you have supports the mss-adjust.

The symptoms are typical of the problem, please enable it on the ethernet inside and if doesn't work, at least it's ruled out.

New Member

Re: Can't browse certaing sites through dialer interface

mtl01rt01ec(config-if)#ip tcp ?

compression-connections Maximum number of compressed connections

header-compression Enable TCP header compression

mtl01rt01ec(config-if)#ip tcp

This is what I get. No option for mss.

Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

So you were able to configure for dialer and not for ethernet ?

Also can you try "ip adjust-mss 1452" ?

New Member

Re: Can't browse certaing sites through dialer interface

These are the options that I have.

Yeah, the dialer has been in place for two years.

mtl01rt01ec(config-if)#ip ?

Interface IP configuration subcommands:

access-group Specify access control for packets

accounting Enable IP accounting on this interface

address Set the IP address of an interface

authentication authentication subcommands

bandwidth-percent Set EIGRP bandwidth limit

bgp BGP interface commands

broadcast-address Set the broadcast address of an interface

cef Cisco Express Fowarding interface commands

cgmp Enable/disable CGMP

directed-broadcast Enable forwarding of directed broadcasts

dvmrp DVMRP interface commands

hello-interval Configures IP-EIGRP hello interval

helper-address Specify a destination address for UDP broadcasts

hold-time Configures IP-EIGRP hold time

igmp IGMP interface commands

irdp ICMP Router Discovery Protocol

load-sharing Style of load sharing

mask-reply Enable sending ICMP Mask Reply messages

mrm Configure IP Multicast Routing Monitor tester

mroute-cache Enable switching cache for incoming multicast packets

mtu Set IP Maximum Transmission Unit

multicast IP multicast interface commands

nat NAT interface commands

nhrp NHRP interface subcommands

ospf OSPF interface commands

pgm PGM Reliable Transport Protocol

pim PIM interface commands

policy Enable policy routing

probe Enable HP Probe support

proxy-arp Enable proxy ARP

rarp-server Enable RARP server for static arp entries

redirects Enable sending ICMP Redirect messages

rgmp Enable/disable RGMP

rip Router Information Protocol

route-cache Enable fast-switching cache for outgoing packets

rsvp RSVP interface commands

rtp RTP parameters

sap Session Advertisement Protocol interface commands

sdr Session Directory Protocol interface commands

security DDN IP Security Option

split-horizon Perform split horizon

summary-address Perform address summarization

tcp TCP header compression parameters

unnumbered Enable IP processing without an explicit address

unreachables Enable sending ICMP Unreachable messages

urd Configure URL Rendezvousing

verify Enable per packet validation

vrf VPN Routing/Forwarding parameters on the interface

wccp WCCP interface commands

New Member

Re: Can't browse certaing sites through dialer interface

It didn't work. Any other ideas?

Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

Sorry, it should be "ip tcp adjust-mss" under eth interface. If you don't have the option, need to upgrade IOS.

New Member

Re: Can't browse certaing sites through dialer interface

I'm using a dialer interface to pass credentials to the dsl provider.

Hall of Fame Super Gold

Re: Can't browse certaing sites through dialer interface

Ok, were you able to put the above suggested mss-adjust commands in the lan interface ?

136
Views
0
Helpful
12
Replies
CreatePlease to create content