Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Can't see FXS card

Hi;

I have 2811 router with serial & FXS cards.

I can't find the FXS card??

-----

R1#sh ve

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Wed 22-Feb-06 16:37 by ccai

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(8)T6, R)

R1 uptime is 9 minutes

System returned to ROM by reload at 21:19:18 UTC Thu Apr 12 2007

System image file is "flash:c2800nm-adventerprisek9_ivs-mz.124-4.T2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.

Processor board ID FTX1032A2CP

2 FastEthernet interfaces

2 Serial(sync/async) interfaces

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

9 REPLIES
Hall of Fame Super Gold

Re: Can't see FXS card

Show diag please ?

Community Member

Re: Can't see FXS card

hi;

when i do show diag .. the i get the following :S

R1#show diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

Onboard VPN : v2.2.0

EEPROM contents at hardware discovery:

PCB Serial Number : FOC10303E35

Hardware Revision : 3.0

Top Assy. Part Number : 800-26920-03

Board Revision : A0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20060801

Chassis Serial Number : FTX1032A2CP

Chassis MAC Address : 0019.0685.73e0

MAC Address block size : 24

CLEI Code : COM7C00ARA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-04

Version Identifier : V04

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 31 30 33 30 33 45 33 35 40

0x10: 03 E7 41 03 00 C0 46 03 20 00 69 28 03 42 41 30

0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 32 1A 81 C2 8B 46 54 58 31 30 33 32

0x40: 41 32 43 50 C3 06 00 19 06 85 73 E0 43 00 18 C6

0x50: 8A 43 4F 4D 37 43 30 30 41 52 41 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 04 89 56 30 34 00 D9 02 40 C1 FF FF FF FF FF FF

WIC Slot 0:

Serial 2T (12in1)

Hardware revision 1.0 Board revision G0

Serial number 28646321 Part number 800-03181-01

FRU Part Number WIC-2T=

Test history 0x0 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 12 01 00 01 B5 1B B1 50 0C 6D 01 00 00 00 00

0x30: 80 00 00 00 02 06 24 00 FF FF FF FF FF FF FF FF

WIC Slot 1:

FXS Voice daughter card (2 port)

WIC module not supported/disabled in this slot

Hardware revision 1.1 Board revision B0

Serial number 29954157 Part number 800-02493-04

FRU Part Number VIC-2FXS=

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 0E 01 01 01 C9 10 6D 50 09 BD 04 00 00 00 00

0x30: 58 00 00 00 03 03 04 01 FF FF FF FF FF FF FF FF

Re: Can't see FXS card

Hi Waleed

I think your ISR router doesn't support the VIC-2FXS card which you are using.

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094fac.shtml

HTH

L.Thot

Community Member

Re: Can't see FXS card

Dear;

thanks for the prompt

but do you have idea what sgould i do?

Bronze

Re: Can't see FXS card

Sure thing..

c2800nm-ipvoicek9-mz.124-13a.bin

That's the latest LD version for IP VOICE.

Please let me know if that helps your FXS card being not recognized.

Bronze

Re: Can't see FXS card

Hello,

I have experienced this exact same problem and had to download a version of IOS that supported voice. Login to CCO and utilize the Software Advisor.

Community Member

Re: Can't see FXS card

Ok; thanks i will but i tried the following images:

c2800nm-ipvoicek9-mz.124-12a.bin

c2800nm-adventerprisek9_ivs-mz.124-4.T2.bin

do you have exact image name?

thanks

Bronze

Re: Can't see FXS card

I missed this one, but thotsaphon was totally correct... You have a VIC-2FXS card but you if you want that functionality on a 2811 you need to install a VIC2-2FXS card.

Make sure to credit thotsaphon with the correct answer and make sure to check out his link. If you scroll down to find the 2811 in the table you will see what is and what is not supported.

Community Member

Re: Can't see FXS card

Thanks i got it.

i loosed 4X cards :D

345
Views
25
Helpful
9
Replies
CreatePlease to create content