08-08-2013 10:40 AM - edited 03-04-2019 08:42 PM
Hi All.
I'm having a bit of a nightmare trying to get the VDSL interface to work on my 887 router. It was working just fine on standard ADSL but now i have moved over to VDSL i cant seem to get it connected. When i connect the RJ11 into the back of the router i see the below with logging enabled in the console (seems to be a constant cycle of Virtual-Access1 being up/down):
TheBeast#
Aug 8 17:21:50.282: %CONTROLLER-5-UPDOWN: Controller VDSL 0, changed state to up
Aug 8 17:21:53.290: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
Aug 8 17:22:28.034: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
Aug 8 17:22:28.038: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Aug 8 17:22:28.642: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di0
Aug 8 17:22:28.646: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Aug 8 17:22:50.822: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
Aug 8 17:22:50.826: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Aug 8 17:22:51.214: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di0
Aug 8 17:22:51.218: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Aug 8 17:23:13.654: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
Aug 8 17:23:13.658: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Aug 8 17:23:13.998: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di0
Aug 8 17:23:13.998: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Aug 8 17:23:36.674: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
Aug 8 17:23:36.678: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Aug 8 17:23:37.230: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di0
Aug 8 17:23:37.234: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Aug 8 17:23:59.534: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
Aug 8 17:23:59.538: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
ATM0 interface has been shut since changing from dsl.
My config is below. Can anyone advise?
Building configuration...
Current configuration : 2345 bytes
!
! Last configuration change at 17:19:47 UTC Thu Aug 8 2013
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname TheBeast
!
boot-start-marker
boot-end-marker
!
!
enable secret 4 #########################
!
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
!
!
ip source-route
!
!
!
ip dhcp excluded-address 192.168.0.1
ip dhcp excluded-address 192.168.0.12
!
ip dhcp pool HomeNetwork
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
dns-server 62.24.199.13 62.24.199.23
lease 0 2
!
!
ip cef
no ip domain lookup
no ipv6 cef
!
!
license udi pid CISCO887VA-K9 sn FCZ17119094
!
!
!
controller VDSL 0
firmware filename flash:vdsl.bin-A2pv6C035d_d23j
!
!
!
!
!
!
!
!
interface Ethernet0
no ip address
ip virtual-reassembly in
!
interface Ethernet0.101
encapsulation dot1Q 101
pppoe-client dial-pool-number 1
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
pvc 0/38
pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface Vlan1
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
!
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1432
dialer pool 1
ppp authentication chap callin
ppp chap hostname myispusername
ppp chap password 0 mypassword
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
ip nat inside source list 101 interface Dialer0 overload
ip nat inside source static tcp 192.168.0.12 53 interface Dialer0 53
ip nat inside source static udp 192.168.0.12 53 interface Dialer0 53
ip nat inside source static tcp 192.168.0.12 80 interface Dialer0 80
ip nat inside source static udp 192.168.0.12 88 interface Dialer0 88
ip nat inside source static tcp 192.168.0.12 3074 interface Dialer0 3074
ip nat inside source static udp 192.168.0.12 3074 interface Dialer0 3074
!
access-list 101 permit ip 192.168.0.0 0.0.255.255 any
dialer-list 1 protocol ip permit
!
!
!
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input all
!
end
08-11-2013 03:15 AM
it seems this issue was resolved previous by an IOS update. i cannot do this however as i have no cisco support contract.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide