Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CatOS - Int details

Hi

Not much familiar with CATOS

what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: CatOS - Int details

Hello Saquib,

sh port 1/5

additional counters are reported in

sh mac 1/5

example:

sh port 2/5

* = Configured MAC Address

Port  Name               Status     Vlan       Level  Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5  ptocern404pp1224   connected  605        normal a-full a-1Gb 10/100/1000

Port  AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5  none          none         

Port  Security Violation Shutdown-Time Age-Time Max-Addr Trap     IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5  disabled  shutdown             0        0        1 disabled     353

Port  Num-Addr Secure-Src-Addr     Age-Left Last-Src-Addr     Shutdown/Time-Left

----- -------- -----------------   -------- ----------------- ------------------

2/5         0                 -          -                 -        -         -

Port  Flooding on Address Limit

----- -------------------------

2/5                    Enabled

Port  Send FlowControl  Receive FlowControl   RxPause    TxPause    Unsupported

      admin    oper     admin     oper                              opcodes

----- -------- -------- --------- ---------   ---------- ---------- -----------

2/5  on       disagree desired   off         0          0          0        

Port   Admin Channel LACP Port  Ch   Partner Oper                    Partner

       key   Mode    Priority   id   Sys ID                          Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5    718  passive    128       0      0:00-00-00-00-00-00            0

Port  Status      ErrDisable Reason    Port ErrDisableTimeout  Action on Timeout

----  ----------  -------------------  ----------------------  -----------------

2/5  connected                     -  Enable                  No Change

Port  Align-Err  FCS-Err    Xmit-Err   Rcv-Err    UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5           -          0          0      32127         0

Port  Single-Col Multi-Coll Late-Coll  Excess-Col Carri-Sen Runts     Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5           0          0          0          0         0         0         0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

sh mac 2/5

Port     Rcv-Unicast          Rcv-Multicast        Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5               2701929405                    0              2457154

Port     Xmit-Unicast         Xmit-Multicast       Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5                680508948             19331294               746433

Port     Rcv-Octet            Xmit-Octet

-------- -------------------- --------------------

2/5            3993868326093         103277529193

MAC      Dely-Exced MTU-Exced  In-Discard Lrn-Discrd In-Lost    Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5              0          0      32127          0          0          0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

Hope to help

Giuseppe

3 REPLIES
Hall of Fame Super Blue

Re: CatOS - Int details

saquib.tandel wrote:

Hi

Not much familiar with CATOS

what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5

From memory -

"sh port 1/5"  should do it.

Jon

Silver

Re: CatOS - Int details

Use the "SHOW PORT" command for port details.  The SHOW PORT COUNTERS is another good one. So for your example it will be "SHOW PORT 1/5".. Good Luck..

Hall of Fame Super Silver

Re: CatOS - Int details

Hello Saquib,

sh port 1/5

additional counters are reported in

sh mac 1/5

example:

sh port 2/5

* = Configured MAC Address

Port  Name               Status     Vlan       Level  Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5  ptocern404pp1224   connected  605        normal a-full a-1Gb 10/100/1000

Port  AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5  none          none         

Port  Security Violation Shutdown-Time Age-Time Max-Addr Trap     IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5  disabled  shutdown             0        0        1 disabled     353

Port  Num-Addr Secure-Src-Addr     Age-Left Last-Src-Addr     Shutdown/Time-Left

----- -------- -----------------   -------- ----------------- ------------------

2/5         0                 -          -                 -        -         -

Port  Flooding on Address Limit

----- -------------------------

2/5                    Enabled

Port  Send FlowControl  Receive FlowControl   RxPause    TxPause    Unsupported

      admin    oper     admin     oper                              opcodes

----- -------- -------- --------- ---------   ---------- ---------- -----------

2/5  on       disagree desired   off         0          0          0        

Port   Admin Channel LACP Port  Ch   Partner Oper                    Partner

       key   Mode    Priority   id   Sys ID                          Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5    718  passive    128       0      0:00-00-00-00-00-00            0

Port  Status      ErrDisable Reason    Port ErrDisableTimeout  Action on Timeout

----  ----------  -------------------  ----------------------  -----------------

2/5  connected                     -  Enable                  No Change

Port  Align-Err  FCS-Err    Xmit-Err   Rcv-Err    UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5           -          0          0      32127         0

Port  Single-Col Multi-Coll Late-Coll  Excess-Col Carri-Sen Runts     Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5           0          0          0          0         0         0         0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

sh mac 2/5

Port     Rcv-Unicast          Rcv-Multicast        Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5               2701929405                    0              2457154

Port     Xmit-Unicast         Xmit-Multicast       Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5                680508948             19331294               746433

Port     Rcv-Octet            Xmit-Octet

-------- -------------------- --------------------

2/5            3993868326093         103277529193

MAC      Dely-Exced MTU-Exced  In-Discard Lrn-Discrd In-Lost    Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5              0          0      32127          0          0          0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

Hope to help

Giuseppe

279
Views
0
Helpful
3
Replies
CreatePlease login to create content