Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

Cisco 1841 with point-to-point T1

We have a point-to-point T1 between two Cisco 1841 routers (with WIC-1DSU-T1-V2).

When I perform a "no shut" on either end of the T1, the line protocol comes up for a few seconds and then goes down. Does this look like a config problem or a circuit issue?

MAIN SITE

interface Serial0/0/0

bandwidth 1536

ip address x.x.x.x x.x.x.x

no ip redirects

service-module t1 timeslots 1-24

max-reserved-bandwidth 100

service-policy output WAN-EDGE

end

REMOTE SITE

interface Serial0/0/0

bandwidth 1536

ip address x.x.x.x x.x.x.x

no ip redirects

service-module t1 timeslots 1-24

max-reserved-bandwidth 100

service-policy output WAN-EDGE

end

1841-router#sh service-module ser0/0/0 performance-statistics

Total Data (last 5 15 minute intervals):

26 Line Code Violations, 825 Path Code Violations

0 Slip Secs, 142 Fr Loss Secs, 22 Line Err Secs, 72 Degraded Mins

567 Errored Secs, 99 Bursty Err Secs, 3 Severely Err Secs, 139 Unavail Secs

Data in current interval (156 seconds elapsed):

0 Line Code Violations, 19 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 3 Degraded Mins

16 Errored Secs, 3 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 1:

3 Line Code Violations, 98 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 15 Degraded Mins

90 Errored Secs, 8 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 2:

10 Line Code Violations, 213 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 8 Line Err Secs, 15 Degraded Mins

114 Errored Secs, 32 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 3:

2 Line Code Violations, 100 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 15 Degraded Mins

90 Errored Secs, 10 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 4:

11 Line Code Violations, 182 Path Code Violations

0 Slip Secs, 139 Fr Loss Secs, 9 Line Err Secs, 13 Degraded Mins

142 Errored Secs, 19 Bursty Err Secs, 0 Severely Err Secs, 139 Unavail Secs

Data in Interval 5:

0 Line Code Violations, 232 Path Code Violations

0 Slip Secs, 3 Fr Loss Secs, 0 Line Err Secs, 14 Degraded Mins

131 Errored Secs, 30 Bursty Err Secs, 3 Severely Err Secs, 0 Unavail Secs

1 REPLY
Highlighted
Hall of Fame Super Gold

Re: Cisco 1841 with point-to-point T1

Hi, as you can see the circuits is severely errored, check again linecode and framing settings. You may need to report circuit failure to SP.

396
Views
3
Helpful
1
Replies
CreatePlease to create content