Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

cisco 2911 + DSL

Hi.

Having configure a several 2911 with EHWIC-VA-DSL-M onboard. Have succesfully configured about 5 routers in the absolutly same configuration,

ver of a IOS, firmware modem and so on.

But in one of the 2911 have problem - it does not connect to dsl. Debug atm showed this (even I wasn't plug telephone cable int the 2911 port)


*Mar  6 16:08:26 NSK: (atm_vc_is_bridged_dot1q)ATM: VC with handle 0x0 not found
*Mar  6 16:08:26 NSK: VC micro block get: Invalid vc handle
*Mar  6 16:08:26 NSK: VC micro block get: Invalid vc handle
*Mar  6 16:08:26 NSK: (atm_vc_get_from_vc_hdl): Invalid vc handle 0

When I connect the telephone cable - logging message is the same, no reaction.

Config of the interfaces

interface ATM0/0/0
   no ip address
  no atm ilmi-keepalive
  pvc 0/35
   encapsulation aal5snap
   pppoe-client dial-pool-number 1
  !
!
interface Dialer1
   ip address negotiated
  encapsulation ppp
  ip tcp adjust-mss 1390
  dialer pool 1
  dialer-group 1
  ppp pap sent-username ***** password 0 *****
  no cdp enable

Here some usefull information

sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M5, RELEASE SOFTWARE (fc2)


sh controllers vdsL 0/0/0
Controller VDSL 0/0/0 is DOWN

Daemon Status:           Establishing Link

                        XTU-R (DS)              XTU-C (US)
Chip Vendor ID:         'BDCM'                   '    '
Chip Vendor Specific:   0x0000                   0x0000
Chip Vendor Country:    0xB500                   0x0000
Modem Vendor ID:        'CSCO'                   '    '
Modem Vendor Specific:  0x4602                   0x0000
Modem Vendor Country:   0xB500                   0x0000
Serial Number Near:    FOC17443KRU 2911/K9  15.2(4)M
Serial Number Far:
Modem Version Near:    15.2(4)M
Modem Version Far:

Modem Status:            Idle
DSL Config Mode:        AUTO
Trained Mode:
TC Mode:                 UNKNOWN
Selftest Result:         0x00
DELT configuration:      disabled
DELT state:              not running
Trellis:                 OFF                      OFF
SRA:                     disabled                        disabled
  SRA count:              0                       0
Bit swap:                enabled                         enabled

Full inits:             0
Failed full inits:      0
Short inits:            0
Failed short inits:     0

Firmware        Source          File Name (version)
--------        ------          -------------------
VDSL            embedded        VDSL_LINUX_DEV_01212008 (1)

Modem FW  Version:      130205_1433-4.02L.03.A2pv6C035j.d23j
Modem PHY Version:      A2pv6C035j.d23j
Vendor Version:         Ap6v35j.23j 68

My searching on the Internet gived me this link

https://supportforums.cisco.com/thread/2209556

Tried to using this solution then reboot the router

operating mode adsl2+

but have no success.

Is it something wrong with EHWIC-VA-DSL-M or what could be?

Thanks

Everyone's tags (4)
781
Views
0
Helpful
0
Replies