Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CISCO 3745 error

hi

The following error displayed in console.Please help me to boot this router

error:

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 2002 by cisco Systems, Inc.

c3745 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

rommon 1 >

thanks in advance

7 REPLIES
New Member

Re: CISCO 3745 error

Hi,

Its not an error , your device is in rommon mode.Please find the below link to recover the device from rommon mode:-

http://www.cisco.com/en/US/products/hw/routers/ps282/products_tech_note09186a008075fd05.shtml#rmon11

or

http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a008009429f.shtml

Hope this helps.

Regards

Sum

New Member

Re: CISCO 3745 error

hi

the following messages displayed

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 2002 by cisco Systems, Inc.

c3745 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

program load complete, entry point: 0x80008000, size: 0x6af738

Error : compressed image checksum is incorrect 0x87CF42D9

Expected a checksum of 0x42EF42D9

*** System received a Software forced crash ***

signal= 0x17, code= 0x5, context= 0x0

PC = 0x800080d4, Cause = 0x20, Status Reg = 0x3041a803

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 2002 by cisco Systems, Inc.

c3745 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

rommon 1 >

Hall of Fame Super Gold

Re: CISCO 3745 error

Try realoding the image or boot straight without writing to flash, using the option in tftpdnld.

New Member

Re: CISCO 3745 error

Hi

After reloading new image the follwing error displayed.

Copyright (c) 2002 by cisco Systems, Inc.

c3745 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

program load complete, entry point: 0x80008000, size: 0x11605dc

*** TLB (Load/Fetch) Exception ***

Access address = 0x7074e

PC = 0x8040ad90, Cause = 0x8, Status Reg = 0x3041a803

monitor: command "boot" aborted due to exception

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 2002 by cisco Systems, Inc.

c3745 processor with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

rommon 1 >

Regs

S.Mohan

Hall of Fame Super Gold

Re: CISCO 3745 error

Were you trying to upgrade the memory before this error message started appearing?

New Member

Re: CISCO 3745 error

No.Nothing changed in hardware.i am reloading image through rommon mode with xmodem command.

regs

s.mohan

Silver

Re: CISCO 3745 error

Hi ,

Another simple way to load new image is first load the image in RAM using xmodem command ie ..

xmodem filename -r

Router boots with the image stored in DRAM.

After that make sure that router is not reloaded until you load the image to flash using tftp server.

Once you load the image using tftp reload the router and make sure that config-reg value must be 0x2102.

If you face the same problem after following the above procedure check the flash once.

Hope this helps you.

Thanks,

Satish

462
Views
0
Helpful
7
Replies