Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CISCO 3845: Error %PSE HW—1—PKT ERROR: preparing paktype of SM CONTROL PACKET

Hello,

i have an error with my cisco router 3845, during reboot i there one error:

%PSE HW—1—PKT ERROR: preparing paktype of SM CONTROL PACKET

Does the error is complied

Installed image archive

Cisco 3845 (revision 1.0) with 221184K/40960K bytes of memory.



Processor board ID FCZ133670YY
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco ips sensor(s), ips monitoring on slot O
DRAM configuration is 64 bits wide with parity enabled.
447K bytes of NVRAM.
250880K bytes of ATA System CompactFlash (Read/Write)
*Feb 11 12:52:17.347: %PSE HW—1—PKT ERROR: preparing paktype of SM CONTROL PACKET
*Feb 11 12:52:44.451: %VPN MW—6—INFO LOC: Crypto engine: onboard O State changed to: Initialized
*Feb 11 12:52:44.455: %VPN MW—6—INFO LOC: Crypto engine: onboard O State changed to: Enabled
*Feb 11 12:52:45.423: %LINK—3—UPDOWN: Interface GigabitEthernetO/O, changed state to up
*Feb 11 12:52:45.423: %LINK—3—UPDOWN: Interface GigabitEthernetO/1, changed state to up
*Feb 11 12:52:45.427: %LINEPROTO—5—UPDOWN: Line protocol on Interface VoIP—NullO, changed state to up
*Feb 11 12:52:45.651: %LINEPROTO—5—UPDOWN: Line protocol on Interface Onboard VPN, changed state to up
*Feb 11 12:52:46.431: %LINEPROTO—5—UPDOWN: Line protocol on Interface GigabitEtherneto/0, changed state to up
*Feb 11 12:52:46.431: %LINEPROTO—5—UPDOWN: Line protocol on Interface GigabitEtherneto/1, changed state to down
*Feb 11 12:52:46.443: %LINEPROTO—5—UPDOWN: Line protocol on Interface IDS—SensorO/O, changed state to up

Thanks for help

Alex

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Gold

CISCO 3845: Error %PSE HW—1—PKT ERROR: preparing paktype of

Here is one possibility:

AIM-IPS-K9:PSE_HW-1-PKT_ERROR' on boot-up

CSCsq24774

Symptom:

When an AIM-IPS-K9 is installed, a router will display the following message as a part of its boot-up process.

%PSE_HW-1-PKT_ERROR: preparing paktype of SM_CONTROL_PACKET

1 REPLY
Gold

CISCO 3845: Error %PSE HW—1—PKT ERROR: preparing paktype of

Here is one possibility:

AIM-IPS-K9:PSE_HW-1-PKT_ERROR' on boot-up

CSCsq24774

Symptom:

When an AIM-IPS-K9 is installed, a router will display the following message as a part of its boot-up process.

%PSE_HW-1-PKT_ERROR: preparing paktype of SM_CONTROL_PACKET

167
Views
0
Helpful
1
Replies