Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CISCO 3845 HWIC-2FE IS NOT DETECTED

Hi,

I have cisco 3845 router with 4 HWIC-2FE card none of them is detected the message displayed is

Oct 4 11:21:35.323: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

*Oct 4 11:21:35.323: fe_mrvl_hw_init : Could not load driver

*Oct 4 11:21:35.323: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to intialize the Marvell switch for FE

, -Traceback= 0x60EA608C 0x605D78B4 0x605D74DC 0x60590528 0x60599724 0x6058D23C 0x602CDA14 0x61F18D6C 0x60E9A9A0 0x60E9AC80 0x61EDAC68 0x61EDAC4Chwic_fe_analyze_interface: Couldn't initialize the HWIC FE

*Oct 4 11:21:36.175: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

*Oct 4 11:21:36.175: fe_mrvl_hw_init : Could not load driver

*Oct 4 11:21:36.175: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to intialize the Marvell switch for FE

, -Traceback= 0x60EA608C 0x605D78B4 0x605D74DC 0x60590528 0x60599724 0x6058D23C 0x602CDA14 0x61F18D6C 0x60E9A9A0 0x60E9AC80 0x61EDAC68 0x61EDAC4Chwic_fe_analyze_interface: Couldn't initialize the HWIC FE

*Oct 4 11:21:37.027: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

Router>

Router>

*Oct 4 11:21:37.031: fe_mrvl_hw_init : Could not load driver

*Oct 4 11:21:37.031: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to intialize the Marvell switch for FE

, -Traceback= 0x60EA608C 0x605D78B4 0x605D74DC 0x60590528 0x60599724 0x6058D23C 0x602CDA14 0x61F18D6C 0x60E9A9A0 0x60E9AC80 0x61EDAC68 0x61EDAC4Chwic_fe_analyze_interface: Couldn't initialize the HWIC FE

*Oct 4 11:21:37.883: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

*Oct 4 11:21:37.883: fe_mrvl_hw_init : Could not load driver

*Oct 4 11:21:37.883: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to intialize the Marvell switch for FE

, -Traceback= 0x60EA608C 0x605D78B4 0x605D74DC 0x60590528 0x60599724 0x6058D23C 0x602CDA14 0x61F18D6C 0x60E9A9A0 0x60E9AC80 0x61EDAC68 0x61EDAC4Chwic_fe_analyze_interface: Couldn't initialize the HWIC FE

Please let me know how to resolve this.

7 REPLIES
Hall of Fame Super Bronze

Re: CISCO 3845 HWIC-2FE IS NOT DETECTED

Card failure - please contact TAC for assistance and request a RMA.

__

Edison.

New Member

Re: CISCO 3845 HWIC-2FE IS NOT DETECTED

Dear Editortiz,

Thanks for ur reply.

Regards,

Jeelany

New Member

Re: CISCO 3845 HWIC-2FE IS NOT DETECTED

I upgraded the IOS and it is working fine now.

New Member

CISCO 3845 HWIC-2FE IS NOT DETECTED

Hi,

Can you plz tell me whats the procedure we have to follow..i m also going to do the same change in my router

CISCO 3845 HWIC-2FE IS NOT DETECTED

install solar winds or any freeware tftp server on your laptop

then on the 3845:

conf t

tftp server flash:

end

!

copy tftp flash

enter ip address of remote tftp server (your laptop)

enter name of the file (the ios name on your laptop, don't forget the .bin extension)

and enjoy it.

before rebooting  specify what the router has to load with the boot command:

conf t

boot system flash:/name_of_copied_ios_  (check the synopsys of this command and point at the right location of your flash memory)

wr

!

reload

yes

!

!


keep in mind you can even use a flash card with a 3845!!!

HTH

Alessio

New Member

CISCO 3845 HWIC-2FE IS NOT DETECTED

Thanks dude..but the thing is i am going to insert HWIC card to my 3845 router..can u plz tell me d procedure

CISCO 3845 HWIC-2FE IS NOT DETECTED

Hi Kumar,

if you refer to the physical procedures nothing is beter than the documentation that cisco provides with the card. I don't remember if it is hot-swap (inserting the card without switching off the router) but it is very very very worth to check on that documenation.

by the way, let me give you this link:

http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/fe_hwic.html

it'll help you. it is very easy everything.

Careful to this... Since you need to reboot the router to load the newer IOS, beter you follow these steps:

1) load the new ios

2)switch off the router and install the card

3) boot the router again

If you did everything correctly it should everything work straight away without further reboot

HTH

Alessio

3455
Views
4
Helpful
7
Replies