Dear Cisco Community,
due to the need of increased bandwidth a customer ordered three ADSL6000/576Kbit lines from the same ISP. Dial-in is done with PPPoE and the IP is not static.
- Is it possible to load balance between the three ISP lines with this router as the Cisco 886VA-K9 (Advanced IP Services) doesnt support PFR/OER I want to load balance per session, meaning each TCP session takes the same path, the next TCP session takes second path, next TCP session takes third path, then first path again and so on.
- I did read the tutorials avaiable, but they don't discuss how the lines are used in round-robin fashion, just how to distribute different traffic on different lines. (https://supportforums.cisco.com/document/32186/dual-internet-links-nating-pbr-and-ip-sla?page=1) or (http://www.cisco.com/c/en/us/support/docs/ip/network-address-translation-nat/100658-ios-nat-load-balancing-2isp.html)
- How would you solve this challenge?
Relevant config so far:
!
vlan 1
name #LAN#
!
vlan 2
name #WAN-Uplink1#
!
vlan 3
name #WAN-Uplink2#
!
interface FastEthernet0
description #LAN#
switchport access vlan 1
!
interface FastEthernet2
description #WAN-Uplink1#
switchport access vlan 2
no ip address
pppoe enable
pppoe-client dial-pool-number 20
!
interface FastEthernet3
description #WAN-Uplink2#
switchport access vlan 3
no ip address
pppoe enable
pppoe-client dial-pool-number 30
!
interface ATM0
description #WAN-Uplink3#
no ip address
logging event atm pvc state
logging event atm pvc autoppp
logging event subif-link-status
no atm ilmi-keepalive
no ip redirects
no ip unreachables
no ip proxy-arp
dsl enable-training-log delay 0
dsl bitswap both
!
interface ATM0.1 point-to-point
bandwidth 550
bandwidth receive 6000
pvc pvc 1/32
pppoe enable
pppoe-client dial-pool-number 10
vbr-nrt 500 500 1
service-policy out WAN-Control1-Parent
!
!
!
interface Vlan1
description #LAN#
ip address 172.16.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer1
description #WAN-Dialer1#
bandwidth 550
bandwidth receive 6000
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 20
dialer idle-timeout 0
ppp authentication chap pap callin
ppp chap hostname XXX
ppp chap password XXX
ppp pap sent-username XXX
ppp ipcp dns request accept
ppp ipcp route default
ppp ipcp address accept
no cdp enable
service-policy output WAN-Control2-Parent
!
!
interface Dialer2
description #WAN-Dialer2#
bandwidth 550
bandwidth receive 6000
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 30
dialer idle-timeout 0
ppp authentication chap pap callin
ppp chap hostname XXX
ppp chap password XXX
ppp pap sent-username XXXX
ppp ipcp dns request accept
ppp ipcp route default
ppp ipcp address accept
no cdp enable
service-policy output WAN-Control3-Parent
!
!
interface Dialer3
description #WAN-Dialer3-ATM#
bandwidth 550
bandwidth receive 6000
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 10
dialer idle-timeout 0
ppp authentication chap pap callin
ppp chap hostname XXX
ppp chap password 7 XXX
ppp pap sent-username xxx
ppp ipcp dns request accept
ppp ipcp route default
ppp ipcp address accept
no cdp enable
!
!
ip nat inside source route-map ISP1 interface Dialer1 overload
ip nat inside source route-map ISP2 interface Dialer2 overload
ip nat inside source route-map ISP3 interface Dialer3 overload
!
!
route-map ISP1 permit 10
match ip address 100
match interface Dialer1
!
route-map ISP2 permit 10
match ip address 100
match interface Dialer2
!
route-map ISP3 permit 10
match ip address 100
match interface Dialer3
!
access-list 100 remark #NAT-LIST#
access-list 100 permit ip 172.16.1.0 0.0.0.255 any
!
Thank you for helping.
