Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco AS 5850 RAS problem

have a problem with Cisco As 5850 RAS. It got hang after every 2-3 days and at that time customers found unable to connect with the server. We have to power-reset the RAS to make it working again. In SHOW-LOGGING command it shows the following Errors:

>

>

>

>

>

> 00:01:22: %DSC_ENV-1-WARNING: Slot 24, AC Shelf warning, Flags = 0 ; Check shelf

>

> status

>

> 00:01:22: %DSC_ENV-1-WARNING: Slot 25, AC Shelf warning, Flags = 0 ; Check shelf

>

> status

>

> 00:01:55: %DSIPPF-5-DS_HELLO: DSIP Hello from shelf 0 slot 5 Succeeded

>

> 00:01:58: %DSIPPF-5-DS_HELLO: DSIP Hello from shelf 0 slot 0 Succeeded

>

> 00:01:59: %CONTROLLER-5-UPDOWN: Controller E1 0/0, changed state to up

>

> 00:01:59: %DSCCLOCK-5-SWITCH1: Clock moving to NORMAL from FREERUN, selected clo

>

> ck is on slot 0 port 0 line 0

>

> 00:01:59: %DIAL0-3-MSG:

>

> 00:00:20: %TRUNK-3-BADCLOCK: Selected clock on slot 0 port 0 is bad. Accepting t

>

> he config.

>

> 00:02:00: %ISDN-6-LAYER2UP: Layer 2 for Interface Se0/0:15, TEI 0 changed to up

>

> 00:02:15: %SPE-3-SM_POST_FAILED: SPE 5/01 is BAD.

>

> 00:02:23: %NP_EST-6-DIAG_POST_NTF: (NP address 5/0/0/1), Test ID=SPE_POWER_ON_SE

>

> LF_TEST, Result=SPE_POST_TEST_FAILED, Diag code=0xFD000003, Data format=Binary,

>

> Data len=28, Data=00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

>

> 00 00 00 00 00 00 00

>

>

>

>

>

> Please help me to find out the specific problem(is it problem with RSC card or supply or Trunk card). Because the same card was working well from last 3 years on the same configuration.

>

2 REPLIES
Bronze

Re: Cisco AS 5850 RAS problem

The Error message %DSC_ENV-1-WARNING: Slot 25, AC Shelf warning, Flags = 0 ; Check shelf status states The card enviromental parameters specified are outside the normal range of operation.

Recommended Action: Check blowers and ambient room temperature.

DSCEXTCLK Messages

The following are Controller Card Clock notification messages.

This error message %SPE-3-SM_POST_FAILED: SPE 5/01 is BAD a state The SPE has failed the POST, and it will be marked as bad.

%NP_EST-6-DIAG_POST_NTF is EST Diagnostic and POST Notification has been sent to the Cisco IOS software to convey additional information about the power-on self-test or a diagnostic test result.

New Member

Re: Cisco AS 5850 RAS problem

Sir, Thanx for ur coordination...

I hav checked the fan assembly and the room temp. But both are ok & the temp is below 20'c.

What is SPE(%SPE-3-SM_POST_FAILED: SPE 5/01). Is it on Trunk/PRI card???? My PRI CARD IS inserted in 0th slot and universal card is inserted in 5th slot.

According to you what can be the final result. Or what should I do to solve the problem???

372
Views
0
Helpful
2
Replies