Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco3845-Cisco3660 and AIM-COMPR4

Good day.

I have 2 router:Cisco3845 and Cisco3660.

They conected using FrameRelay point-to-point:

Router1#

!

interface Hssi1/0

no ip address

encapsulation frame-relay

no ip mroute-cache

load-interval 30

serial restart-delay 0

cdp enable

frame-relay traffic-shaping

frame-relay interface-dlci 20 switched

class h

frame-relay interface-queue priority 450 100 100 400

!

interface Hssi1/0.17 point-to-point

ip address 192.168.1.29 255.255.255.252

frame-relay class data

frame-relay interface-dlci 17

!

interface Hssi1/0.18 point-to-point

ip address 192.168.137.26 255.255.255.252

frame-relay class voice

frame-relay interface-dlci 18

frame-relay ip rtp header-compression

!

...

!

map-class frame-relay data

frame-relay cir 8400000

frame-relay bc 840000

frame-relay be 840000

frame-relay mincir 98000

frame-relay adaptive-shaping becn

frame-relay fair-queue

frame-relay interface-queue fair queue-limit 32

frame-relay interface-queue priority low

!

map-class frame-relay voice

frame-relay cir 8400000

frame-relay bc 840000

frame-relay be 840000

frame-relay mincir 6028000

frame-relay adaptive-shaping becn

frame-relay fair-queue

frame-relay interface-queue fair queue-limit 32

frame-relay interface-queue priority high

!

router2#

!

interface Hssi2/0

no ip address

encapsulation frame-relay

no ip mroute-cache

load-interval 30

serial restart-delay 0

cdp enable

frame-relay traffic-shaping

frame-relay interface-dlci 20 switched

class h

frame-relay intf-type dce

frame-relay interface-queue priority 350 100 100 400

!

interface Hssi2/0.17 point-to-point

ip address 192.168.1.30 255.255.255.252

frame-relay class data

frame-relay interface-dlci 17

!

interface Hssi2/0.18 point-to-point

ip address 192.168.137.25 255.255.255.252

frame-relay class voice

frame-relay interface-dlci 18

frame-relay ip rtp header-compression

!

...

!

map-class frame-relay data

frame-relay adaptive-shaping becn

frame-relay cir 17900000

frame-relay bc 1790000

frame-relay be 1790000

frame-relay mincir 3804000

frame-relay fair-queue

frame-relay interface-queue priority low

!

map-class frame-relay voice

frame-relay adaptive-shaping becn

frame-relay cir 17900000

frame-relay bc 1790000

frame-relay be 1790000

frame-relay mincir 12000000

frame-relay fair-queue

frame-relay interface-queue priority high

!

When I install AIM-COMPR4 card on both router and write comand:

frame-relay payload-compress data-stream stac on interface Hssi2/0.18 point-to-point and interface Hssi1/0.18 point-to-point

I have nutch packet lost on router2# (Cisco 3660) 3660#sh compress

Hssi2/0 - DLCI: 18

Hardware compression enabled

CSA in slot 0 in use

uncompressed bytes xmt/rcv 112931766/167113853

compressed bytes xmt/rcv 14014362/153973667

Compressed bytes sent: 14014362 bytes 7 Kbits/sec ratio: 8.058

Compressed bytes recv: 153973667 bytes 84 Kbits/sec ratio: 1.085

resyncs 128406

last clearing of counters: 14528 seconds

Additional Stac Stats:

Transmit bytes: Uncompressed = 6351074 Compressed = 6365848

Received bytes: Compressed = 142596663 Uncompressed = 0

Can any one answer: Whats a hapend?

4 REPLIES
Hall of Fame Super Gold

Re: Cisco3845-Cisco3660 and AIM-COMPR4

Where do you see the errors ?

New Member

Re: Cisco3845-Cisco3660 and AIM-COMPR4

When I input command on router 3660: 2# sh compress I see to much "resyncs", near 128406 in 2 minites. And if I try to ping ip address on router #1 (3845), there near 50% lost pakets.

If I delete command #"frame-relay payload-compress data-stream stac" from FrameRelay interfase, after this if I try to ping ip address on router #1 (3845), there no any lost pakets.

Hall of Fame Super Gold

Re: Cisco3845-Cisco3660 and AIM-COMPR4

If you ping end-to-end (not from routers but from end systems) do you have packet loss with compression enabled ?

New Member

Re: Cisco3845-Cisco3660 and AIM-COMPR4

Yes, I have packet lost, when i ping end-to-end with compression enabled.

134
Views
0
Helpful
4
Replies