Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

configure atm interface

How do I add this to a router?

interface ATM0/0/0

description ATM Circuit 24.HCGJ.xxxxxx

no ip address

no scrambling-payload

no atm ilmi-keepalive

!

interface ATM0/0/0.36 point-to-point

description Grant Street

ip address 10.XXX.XXX.XXX 255.255.255.252

pvc 1/36

ubr 1382

encapsulation aal5snap

Thanks again!

10 REPLIES
Community Member

Re: configure atm interface

interface ATM x/y

description ATM Circuit 24.HCGJ.xxxxxx

no ip address

no atm ilmi-keepalive

!

interface ATM x/y.36 point-to-point

description Grant Street

ip address 10.XXX.XXX.XXX 255.255.255.252

pvc 1/36

encapsulation aal5snap

Community Member

Re: configure atm interface

How do I add that information to router?

after going into conf t mode, do I need to type each line individually?

Community Member

Re: configure atm interface

you can , or copy the above into notepad, change interface number,description and ip address, then paste all after conf t.U might have to add PVC again.

Community Member

Re: configure atm interface

Thanks mohammedrafig.....

In order to cut and paste, is that done with Hyperterminal? If so, I just tried it and here's how I did that.

1.type conf t

2.copy contents from notepad

3.paste to host

after doing that, I get a % invalid input detected at ?? marker. What am I doing wrong?

Community Member

Re: configure atm interface

can you send us out put of this command,

"sh ver"

Community Member

Re: configure atm interface

This is sho ver

LEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 06-Nov-06 02:36 by alnguyen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

SLB_Grant_St uptime is 20 hours, 3 minutes

System returned to ROM by reload at 20:58:49 UTC Mon Jul 16 2007

System image file is "flash:c2800nm-spservicesk9-mz.124-3g.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.

Processor board ID FTX1122A2PV

2 FastEthernet interfaces

1 ATM interface

1 Channelized T1/PRI port

1 ATM/Voice AIM

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Community Member

Re: configure atm interface

Looks like ur router have not detected the ATM car, or u forgot to install it.

Please send the output of following command

"sh ip int brief"

"sh ver"

Community Member

Re: configure atm interface

This is "sh ip int brief"

SLB_Grant_St#sh ip int brief

Interface IP-Address OK? Method Status Prot

ocol

FastEthernet0/0 10.101.36.1 YES NVRAM up down

FastEthernet0/1 unassigned YES NVRAM administratively down down

ATM0/2/0 unassigned YES unset down dow

Community Member

Re: configure atm interface

U should be able to add the config line by line like this,

SLB_Grant_St# conf t

SLB_Grant_St(conf)#int ATM0/2/0

description ATM Circuit 24.HCGJ.xxxxxx

no ip address

no atm ilmi-keepalive

!

interface ATM 0/2/0.36 point-to-point

description Grant Street

ip address 10.XXX.XXX.XXX 255.255.255.252

pvc 1/36

encapsulation aal5snap

Community Member

Re: configure atm interface

Hi Mohameedrafig,

I am working with another router (2811) and am trying to config the ATM interface. In last post you helped me with slb_grant. Can you please tell me how to add this command to the router?

interface ATM1/0

description 26HCGJXXXXXX

no ip address

ip nbar protocol-discovery

no atm ilmi-keepalive

no scrambling-payload

!

interface ATM1/0.36 point-to-point

bandwidth 1382

ip address 10.XXX.XXX.XXX 255.255.255.252

ip nbar protocol-discovery

pvc 1/36

vbr-rt 1382 1382 1

tx-ring-limit 3

service-policy output Voice

!

!

interface ATM1/1

no ip address

shutdown

no atm ilmi-keepalive

no scrambling-payload

!

interface ATM1/2

no ip address

shutdown

no atm ilmi-keepalive

no scrambling-payload

!

interface ATM1/3

no ip address

shutdown

no atm ilmi-keepalive

no scrambling-payload

419
Views
0
Helpful
10
Replies
CreatePlease to create content