Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Confused about Sh IPv6 route outpout on test exam question.

   Hi.I'm doing a lab test question.It's a simple configuration task for IPv6 and RIPng.I've attached an Image.

There are two routers with a single serial link that each have a lan connected to there fa0/0 interface.When I enter the sh ipv6 route command on either router , I see the RIP learned route to the fa0/0 Interface ends with " via (link local address) , fast ethernet 0/0.I understand the link local addresses for the fast ethernet and serial are the same due to serial interfaces not having a mac address.Why Is the fa0/0 interface mentioned as the outgoing Interface Instead of the routers serial Interface ?

  • WAN Routing and Switching
1 ACCEPTED SOLUTION

Accepted Solutions

Confused about Sh IPv6 route outpout on test exam question.

Good eye...it should be pointing out your s0/0/1 interface as you would expect. It's a problem with the question/simulator. I labbed it up so you can see:

R3#sh ipv6 route

IPv6 Routing Table - 6 entries

Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP

       U - Per-user Static route, M - MIPv6

       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary

       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2

       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

       D - EIGRP, EX - EIGRP external

C   2001:23::/64 [0/0]

     via ::, Serial0/0

L   2001:23::3/128 [0/0]

     via ::, Serial0/0

R   3001:12::/64 [120/2]

     via FE80::C609:B6FF:FEA5:0, Serial0/0

C   3001:34::/64 [0/0]

     via ::, FastEthernet0/0

L   3001:34::3/128 [0/0]

     via ::, FastEthernet0/0

L   FF00::/8 [0/0]

     via ::, Null0

R3#

HTH,

John

HTH, John *** Please rate all useful posts ***
2 REPLIES

Confused about Sh IPv6 route outpout on test exam question.

Good eye...it should be pointing out your s0/0/1 interface as you would expect. It's a problem with the question/simulator. I labbed it up so you can see:

R3#sh ipv6 route

IPv6 Routing Table - 6 entries

Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP

       U - Per-user Static route, M - MIPv6

       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary

       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2

       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

       D - EIGRP, EX - EIGRP external

C   2001:23::/64 [0/0]

     via ::, Serial0/0

L   2001:23::3/128 [0/0]

     via ::, Serial0/0

R   3001:12::/64 [120/2]

     via FE80::C609:B6FF:FEA5:0, Serial0/0

C   3001:34::/64 [0/0]

     via ::, FastEthernet0/0

L   3001:34::3/128 [0/0]

     via ::, FastEthernet0/0

L   FF00::/8 [0/0]

     via ::, Null0

R3#

HTH,

John

HTH, John *** Please rate all useful posts ***
New Member

Confused about Sh IPv6 route outpout on test exam question.

Hi.Thanks for taking a look! I was getting confused there.

187
Views
0
Helpful
2
Replies
This widget could not be displayed.