Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

different output show

Hi ,

I have two different output commands for the same interface atm5/1/0 ?

Every body know why ?

Router #sh int atm5/1/0

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 149357

Output queue :0/140 (size/max)

Router#sh controllers vip 5 tec-support

---

ATM1/0 is up, line protocol is up

Hardware is ENHANCED ATM PA

MTU 4470 bytes, sub MTU 0, BW 34013 Kbit, DLY 200 usec,

reliability 0/255, txload 1/255, rxload 1/255

Encapsulation ATM, loopback not set

Last input never, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 37

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

1406 input errors, 1406 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

-----

router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-PV-M), Version 12.2(7c), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Sat 11-May-02 14:26 by pwade

Image text-base: 0x600109C8, data-base: 0x611C6000

ROM: System Bootstrap, Version 11.1(8)CA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTLDR: RSP Software (RSP-BOOT-M), Version 12.0(17a), RELEASE SOFTWARE (fc1)

wve-tzw-01-abr uptime is 33 weeks, 1 day, 2 hours, 3 minutes

System returned to ROM by reload

System restarted at 11:30:37 MET Tue Mar 7 2006

System image file is "slot0:rsp-pv-mz.122-7c.bin"

cisco RSP4 (R5000) processor with 131072K/2072K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

Chassis Interface.

4 VIP2 R5K controllers (6 FastEthernet)(2 ATM).

6 FastEthernet/IEEE 802.3 interface(s)

2 ATM network interface(s)

123K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

Slave in slot 7 is running Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-DW-M), Version 12.2(7c), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Sat 11-May-02 06:01 by pwade

Slave: Loaded from system

Slave: cisco RSP4 (R5000) processor with 131072K bytes of memory.

Configuration register is 0x102

I attached also router?s show version .

Thanks

Best regards

2 REPLIES
Silver

Re: different output show

The VIP uploads the interface counters to the RSP every 10 seconds or so, after which it clears its own. The best place to look at interface counters on a 7500 is on the RSP itself.

New Member

Re: different output show

Hi,

OK,

But my problems is related to the modify parameters output queue, before it was 40 packets max queue, I put it to 140 packets, we can view this at output show interface atm5/1/0.

But when I looking for output queue parameters in the output commands: show controllers vip 5 tec-supports, I find the older parameters ( 40 packets ).

I try to down load the vip code ( reseat the slot 5 ) but nothings change.

Thank You

Best regards

104
Views
0
Helpful
2
Replies
CreatePlease login to create content