Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

E1 Connection

Dears

I have Site to Site Serial throught E1 connection I created OSPF as we design our network, Any way I have many site all of them working fine, but in the last I add one site througth E1 when I continues ping is giving many Request Time Out. Are this problem with Tranismion Team they have to check The Link or configuration. Because I am to telenet to remote site.

16 REPLIES
Hall of Fame Super Gold

Re: E1 Connection

First check "show controllers e1". Any error is indicative of a problem on the circuit.

New Member

Re: E1 Connection

This is the output please advice:

E1 0/2/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20050620, FPGA: 16, spm_count = 0

Framing is UNFRAMED, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (345 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 10 15 minute intervals):

179 Line Code Violations, 0 Path Code Violations,

2 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 40 Unavail Secs

E1 0/2/1 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20050620, FPGA: 16, spm_count = 0

Framing is UNFRAMED, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (345 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

345 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

345 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 10 15 minute intervals):

8433511 Line Code Violations, 0 Path Code Violations,

7864 Slip Secs, 0 Fr Loss Secs, 9 Line Err Secs, 1 Degraded Mins,

7864 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2202 Unavail Sec

s

Hall of Fame Super Gold

Re: E1 Connection

Is this an ISR router ? If so do you have the required commands ?

network-clock-participate

and

network-clock-select E1 0/2/1 1

New Member

Re: E1 Connection

Still request time out comming

New Member

Re: E1 Connection

What is mean

7864 Slip Secs, 0 Fr Loss Secs, 9 Line Err Secs, 1 Degraded Mins,

Hall of Fame Super Gold

Re: E1 Connection

Means there is clock slippage between circuit clock and router clock. Have you configure the commands ? Please send output of "show network-clocks".

What is on the other side ? You can try turning "clock source internal" on one side of the link only.

Hope this helps, please rate post if it does!

New Member

Re: E1 Connection

EDG-RO1-WMX-JUB#show network-clocks

Network Clock Configuration

---------------------------

Priority Clock Source Clock State Clock Type

1 E1 0/2/1 GOOD E1

11 Backplane GOOD PLL

Current Primary Clock Source

---------------------------

Priority Clock Source Clock State Clock Type

1 E1 0/2/1 GOOD E1

-----------------------------------

REM-R01-ALR-DCK#show network-clocks

Priority 1 clock source: not configured

Priority 2 clock source: not configured

Priority 3 clock source: not configured

Priority 4 clock source: not configured

Priority 5 clock source: Local oscillator

Current clock source:Local oscillator, priority:5

-------------------------------------

EDG-RO1-WMX-JUB#

controller E1 0/2/1

channel-group 0 unframed

!

REM-R01-ALR-DCK#

controller SONET 2/0

framing sdh

!

au-4 1 tug-3 1

tug-2 1 e1 1 unframed

tug-2 1 e1 2 unframed

tug-2 1 e1 3 unframed

tug-2 2 e1 1 unframed

tug-2 2 e1 2 unframed

tug-2 2 e1 3 unframed

tug-2 3 e1 1 unframed

tug-2 3 e1 2 unframed

tug-2 3 e1 3 unframed

tug-2 4 e1 2 unframed

!

au-4 1 tug-3 2

tug-2 7 e1 1 unframed

description "STM-1 Chanalized E1 to remote sites"

The problem in EDG-RO1-WMX-JUB#

Hall of Fame Super Gold

Re: E1 Connection

hi, the only thing you can try is "clock source internal" on edg router, if not that, it's a problem with the circuit and you need to have it fixed.

New Member

Re: E1 Connection

HI Paolo

After I enter the following command clock source internal. The ping is fine for 15 continues ping but after that one request time out and come back 15 or 20 continues ping and the one request time out>>>>> please advice….

Hall of Fame Super Gold

Re: E1 Connection

You have to check "show controllers E1".

As long the slip and error counter is present, something is wrong with the circuit.

New Member

Re: E1 Connection

The error before it was 9 error

but now the errors 0

Hall of Fame Super Gold

Re: E1 Connection

Do clear counter and check there are no more errors.

Also check on the other side, under serial interface, that there are no errors. Probably there are.

New Member

Re: E1 Connection

from another site is SONET Configured please advice.

Hall of Fame Super Gold

Re: E1 Connection

Still you have a logical serial interface for this link on the sonet router, so check for errors on it.

New Member

Re: E1 Connection

11820 input errors, 1854 CRC, 8734 frame, 0 overrun, 0 ignored, 1232 abort

19116 packets output, 11323291 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

Hall of Fame Super Gold

Re: E1 Connection

You have many errors so as mentioned above you need to have the circuit fixed.

237
Views
0
Helpful
16
Replies