Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

EoMPLS on SUP 2

Hi all,

i want to implement EoMPLS on cisco 6500 with this modules

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    2  Catalyst 6000 supervisor 2 (Active)    WS-X6K-SUP2-2GE    SAD063401TP

  2    2  Catalyst 6000 supervisor 2 (Standby)   WS-X6K-SUP2-2GE    SAL08186PTM

  3    4  4-port OC-3c POS SI+                   OSM-4OC3-POS-SI+   SAD074602TP

  4    4  4-port OC-3c POS SI+                   OSM-4OC3-POS-SI+   SAD074602TG

Mod Sub-Module                  Model           Serial           Hw     Status

--- --------------------------- --------------- --------------- ------- -------

  1 Policy Feature Card 2       WS-F6K-PFC2     SAD063301Z6      3.2    Ok

  1 Cat6k MSFC 2 daughterboard  WS-F6K-MSFC2    SAD063404DK      2.6    Ok

  2 Policy Feature Card 2       WS-F6K-PFC2     SAL08186PJ9      3.2    Ok

  2 Cat6k MSFC 2 daughterboard  WS-F6K-MSFC2    SAL08218CGL      2.6    Ok

the IOS version is:

6sup22-pk2sv-mz.121-13.E15.bin

can i do this with the current hardware or i need to replace the SUP or line cards ?

thanks,

Avi.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: EoMPLS on SUP 2

Hi Avi,

no, L2TPv3 is not supported on Cat6500 (or on any other switch).

It is supported on the 7600 (among other routers) with the card combination that you have (sup720 + sip-400) but in the other 'direction', that is the sip-400 (or the ES+) facing the CE and an IP interface on any line card facing the core.

PLEASE RATE THE THREAD AND CLOSE THE THREAD.

Riccardo

6 REPLIES
VIP Super Bronze

EoMPLS on SUP 2

Cisco Employee

EoMPLS on SUP 2

actually since you have an OSM module you can have PXF based EoMPLS (SVI mode) which is the VC configured under the SVI.

Not sure if your IOS already supports it, incase you gotta upgrade to latest available release for Sup2.

Likely the syntax will be the old one (not xconnect)

something like

interface Vlan3
no ip address
mpls l2transport route 10.0.0.1 3 

regards

Riccardo

New Member

EoMPLS on SUP 2

please pay attention that my core facing is OSM so i understand it support EoMPLS, but my LAN facing is GE based on the Supervisor interface.

can i still do it?, i dont know if i can have SVI on that inteface.

thanks,

Avi.

Cisco Employee

EoMPLS on SUP 2

Hi Avi,

OSM must be facing the core. It should be the L3 interface with MPLS enabled.

The SVI is not on that interface as a it is handled by the supervisor in all cases.

Basically the sup will take care of L2 forwarding and MAC learning, while the OSM will do MPLS imposition/disposition. This is what SVI based EoMPLS is all about on Cat6500/7600.

Your CE will be connected to a L2 port (any LAN module will do) controlled by the Sup.

As I wrote I am not sure about the IOS you have.. you can have a quick try to see if the commands are available. By experience I can tell you that the setup you have is working.

Riccardo

New Member

EoMPLS on SUP 2

Thanks,

BTW, can i have L2TPv3 at C6K with sup-720 and sip-400 core facing line card ?

Avi.

Cisco Employee

Re: EoMPLS on SUP 2

Hi Avi,

no, L2TPv3 is not supported on Cat6500 (or on any other switch).

It is supported on the 7600 (among other routers) with the card combination that you have (sup720 + sip-400) but in the other 'direction', that is the sip-400 (or the ES+) facing the CE and an IP interface on any line card facing the core.

PLEASE RATE THE THREAD AND CLOSE THE THREAD.

Riccardo

560
Views
0
Helpful
6
Replies
CreatePlease to create content