Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

failed pings...

could this be cuased by errors on the link?...not even one packet passed..but after i changed the amount..it did..

04#ping

Protocol [ip]:

Target IP address: 192.168.7.73

Repeat count [5]: 100000000

Datagram size [100]: 10000

Timeout in seconds [2]:

Extended commands [n]:

Sweep range of sizes [n]:

Type escape sequence to abort.

Sending 100000000, 10000-byte ICMP Echos to 192.168.7.73, timeout is 2 seconds:

.................................................

Success rate is 0 percent (0/49)

t04#ping

Protocol [ip]:

Target IP address: 192.168.7.73

Repeat count [5]: 10000

Datagram size [100]: 1000

Timeout in seconds [2]:

Extended commands [n]:

Sweep range of sizes [n]:

Type escape sequence to abort.

Sending 10000, 1000-byte ICMP Echos to 192.168.7.73, timeout is 2 seconds:

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!

1 ACCEPTED SOLUTION

Accepted Solutions
Community Member

Re: failed pings...

Look closely...the datagram size in the first set of pings is 10,000...in the second it's 1000. I don't know of any interface that handles 10000-byte packets.

10 REPLIES
Community Member

Re: failed pings...

I think you choose very large number of ping packets on (repeat count), so your router does not able to deal with.

Re: failed pings...

Are you actually having a problem that you're needing to figure out, or is it primarily the high packet count that you're asking the router to push out? I've never used that high of a number before, so I'm not sure what you should expect really.

--John

HTH, John *** Please rate all useful posts ***
Community Member

Re: failed pings...

yes...We are trying to set up etherchannels to HP virtual connect.

The IP is one of the servers on the blades.

The link keeps dropping for some reason.

We are seeing tx/rx errors on the swithcport

of the blades..

but cisco side is totally clean

Re: failed pings...

I would set your speed and duplex settings manually.

HTH, John *** Please rate all useful posts ***
Community Member

Re: failed pings...

thmm..he ping was from a switch to a server

Community Member

Re: failed pings...

Check your datagram size in the first set of pings.

Re: failed pings...

Do you have any errors on the link? The datagram size shouldn't be the problem; it's the same in both pings.

HTH, John *** Please rate all useful posts ***
Community Member

Re: failed pings...

Look closely...the datagram size in the first set of pings is 10,000...in the second it's 1000. I don't know of any interface that handles 10000-byte packets.

Re: failed pings...

Oops...I didn't see that other 0. Good catch. :-)

HTH, John *** Please rate all useful posts ***
Community Member

Re: failed pings...

great..thx!!

163
Views
0
Helpful
10
Replies
CreatePlease to create content