Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Fast Ethernet ports for 7206 VXR

I need at least 4 ports on 7206 VXR.

I guess it should be something like PE-FE....Could someone please let me know the exact part name???

7 REPLIES
Purple

Re: Fast Ethernet ports for 7206 VXR

Hi,

You probably need the PA-2FE-TX and PA-2FE-FX cards. There is more detail on those here:

http://www.cisco.com/en/US/products/hw/modules/ps2033/products_module_installation_guide_chapter09186a0080109103.html

Hope that helps - pls do rate the post if it does.

Paresh

Silver

Re: Fast Ethernet ports for 7206 VXR

You can go for a 2 PE-2FE FX/TX

Silver

Re: Fast Ethernet ports for 7206 VXR

Raj,

Your I/O board may have build-in FE ports (Either one or two). If so you will just need to add 2x PA-FE-TX or 1x PA-2FE-TX / FX

hth,

Ajaz Nawaz

New Member

Re: Fast Ethernet ports for 7206 VXR

Hi Friends...

Thanks for the needful.

I do understand the PA-2FE-TX would serve my purpose but isn't there any Port Adapter (PA) which comes with four ports on a single PA instead of having 2 PAs i.e 2 PA-2FE-TX since I need 4 ethernet ports???

Silver

Re: Fast Ethernet ports for 7206 VXR

If iam right you will get an 8E, a 2 FE and 1 GE, there is no 4 FE in the 7200 PAs

Silver

Re: Fast Ethernet ports for 7206 VXR

Raj,

All the options have been discussed. There is no PA available with more that 2FE ports. If you went down to 10mb then yes, you have PA-8E but I understand this is not what you require.

See this url for all the options available to you:

<http://www.cisco.com/en/US/products/hw/modules/ps2033/ps2546/index.html>

hth,

Ajaz Nawaz

please rate all useful posts.

New Member

Re: Fast Ethernet ports for 7206 VXR

Hi,

not sure if your using an NPE-G1 in you router but the following might be f interest if your going beyond 4 FastEthernet ports on a

router .

Summary:

Oversubscription of bandwidth points is NOT a TAC supported configuration.

Detail:

Cisco 7200 series router with NPE-G1 (3 Gigabit/FastEthernet ports do not take up bandwidth points).

Slots 1,3,5 have a total of 600 bandwidth points max.

Slots 2,4,6 have a total of 600 bandwidth points max.

In all 1200 points

PA-FE-TX/FX = 200 points

PA-2FE-TX/FX = 400 points (.i.e if both ports used)

So:

PA-FE-TX/FX 200 Bandwidth points x 6 = the full 1200 points

PA-2FE-TX/FX 400 Bandwidth points x 6 = 2400 if all ports used

So you can only have a total of six Fastethernet ports on a router.

References:

http://www.cisco.com/application/pdf/en/us/guest/products/ps341/c1161/ccmigration_09186a008009184d.pdf

http://www.cisco.com/en/US/products/hw/modules/ps2033/products_configuration_guide_chapter09186a008014cf5c.html#wp1056349

340
Views
0
Helpful
7
Replies