Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

filter traffic from lan to use different wan circuits

Dear friends..

i have few lines to be exact 3 lines coming on one router i want my LAN users (Single Subnet) .. few to use one circuit to go to wan .. other to use second circuit and rest to use the the thirr or may be in future again divided into forth or fifth circuit ..

dont know if this can be possible via PBR .. please advice with some configuration guidance .. how can i achive this .. thanks for the time and help

11 REPLIES
New Member

filter traffic from lan to use different wan circuits

ip route 192.168.10.0 0.0.0.255 10.10.10.1 ---- lets say your subnet 1 users will go to 10.10.10.1

ip route 192.168.100.0 0.0.0.255 20.20.20.1 ---- lets say your subnet 2 users will go to 20.20.20.1

ip route 192.168.200.0 0.0.0.255 30.30.30.1 ---- lets say your subnet 3 users will go to 30.30.30.1

New Member

filter traffic from lan to use different wan circuits

jigar sir .. read my post ... its a single lan subnet ... three wan lines ..

filter traffic from lan to use different wan circuits

its depend,

tell me, the three connection are puted in the same router or in different router,

i must have more information,

or if you can post a picture of your architecture



New Member

filter traffic from lan to use different wan circuits

.. nice question .. all three lines on same router .. and my setup is already explained on thread start..

filter traffic from lan to use different wan circuits

Hello,

    PBR is good to go for load-sharing. If NAT is there, you may need to read the document below.

Ref: http://www.cisco.com/en/US/tech/tk648/tk361/technologies_configuration_example09186a0080950834.shtml

HTH,

Toshi

New Member

filter traffic from lan to use different wan circuits

Hi,

1st you have to div your singe network into 3 subnets.

then for ex if your network is 10.126.251.X

access-list 100 deny   ip 10.126.251.0 0.0.0.A any

access-list 100 deny   ip 10.126.251.0 0.0.0.B any

access-list 100 permit ip any any

access-list 101 deny   ip 10.126.251.0 0.0.0.C any

access-list 101 deny   ip 10.126.251.0 0.0.0.B any

access-list 101 permit ip any any

access-list 102 deny   ip 10.126.251.0 0.0.0.A any

access-list 102 deny   ip 10.126.251.0 0.0.0.C any

access-list 102 permit ip any any

!

route-map test permit 10

match ip address 100

set ip next-hop (To router 1)

route-map test permit 20

match ip address 101

set ip next-hop (To router 2)

route-map test permit 10

match ip address 102

set ip next-hop (To router 3)

interface lan.

ip policy route-map test

hope it works

Regards,

Satya.M

filter traffic from lan to use different wan circuits

Hi Jatinder,


You can go with PBR, with this you can shape the traffic in which way you want.
See the below example config may helps you.

ip accesslist ext 150
permit 192.168.2.0 0.0.0.255 any
deny any any

ip accesslist ext 151
permit 192.168.3.0 0.0.0.255 any
deny any any

ip accesslist ext 152
permit 192.168.4.0 0.0.0.255 any
deny any any


route-map WAN1 permit 10
match ip address 150


route-map WAN2 permit 10
match ip address 151

route-map WAN3 permit 10
match ip address 152

!
interface 1provider
ip policy route-map WAN1

interface 2provider
ip policy route-map WAN2

interface 3provider
ip policy route-map WAN3

Please rate the helpfull posts.
Regards,
Naidu.

New Member

filter traffic from lan to use different wan circuits

guys guys... i thnk we are missing something .. i cant change my lan subnet .. i need to keep all of them in one subnet.. please advice if this is possible or not ..

New Member

filter traffic from lan to use different wan circuits

Hi,

Not Possibel.

Regards,

Satya.M

New Member

filter traffic from lan to use different wan circuits

Jatinder, I think you need to read some CCNP related books and try to search this one on internet. if you find anything that is doable the way you want, we are happy to get it informed by you in future.

filter traffic from lan to use different wan circuits

sorry for my late i was in travel;

i think the best way is to do 3 nat session ;

example with 4 eth ( 3 wan e0 to e2 and 1 inside e3)

you must creat 3 acl with fragment of your lan example

acces-list 1

acces-list 2

acces-list 3

and after configure the 3 wan interface with ip nat outside

inte fas eth 0 -2

ip nat outside

and

inte fas eth 3

ip nat inside

after with acces list do different session on nat

ip nat inside source list 1 interface Ethernet 0 overload

ip nat inside source list 2 interface Ethernet 1 overload

ip nat inside source list 3 interface Ethernet 2 overload

i thik its work very good.

regards

678
Views
5
Helpful
11
Replies
CreatePlease login to create content