06-26-2012 04:08 AM - edited 03-04-2019 04:47 PM
hi all,ive set up a frame relay lab using a fr switch for multi point also have set up a point to point through the switch to 1 of the mp routers(drawing of topology to be added),the pvcs work and i can ping from first router to both multi points and from multi r1 to multi r2 and can ping the point to point link 2 but cannot ping between p2p and multi point
can ping from r1s0/0.102-103(191.168.123.1)191.168.123.2 s0.201 and 3(multi point) 301
and can ping from r1(191.168.12.1)s0/0.112 to r2 191.16812.2 211 s0/0.211
but cannot ping from 191.168.123.3 to 191.168.12.2
heres the show run from all 3 routers and fr switch
R1
!
version 12.3
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
!
hostname tewys-comm-server
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$Shr4$9O6/xjfAwHjxpmjcxD0c..
!
username chris secret 5 $1$eys4$LG5zu.XkuVocDQCma1X070
username cisco password 7 13061B13181F
no aaa new-model
ip subnet-zero
ip domain list cisco.com
no ip domain lookup
ip host 3620-2 2002 172.21.1.1
ip host 2620-rj 2003 172.21.1.1
ip host 3640-1 2001 172.21.1.1
ip host SW1-1 2004 172.21.1.1
ip host SW3-3 2005 172.21.1.1
ip host 3640-rj 2003 172.21.1.1
ip host 2621-1 2001 172.21.1.1
ip host 2950-1 2004 172.21.1.1
ip host 2950-2 2005 172.21.1.1
ip host 2950-3 2006 172.21.1.1
ip host 3600-3 2014 172.21.1.1
ip host 3600-2 2013 172.21.1.1
ip host 5200-1 2010 172.21.1.1
ip host 2600-1 2008 172.21.1.1
ip host 2509-1 2007 172.21.1.1
ip host 4500-1 2015 172.21.1.1
ip host 3600-1 2012 172.21.1.1
ip host 2600-r2 2002 172.21.1.1
ip host 3640-r3 2003 172.21.1.1
ip host 2621-r1 2001 172.21.1.1
ip host 5200-2 2011 172.21.1.1
ip host 2950-sw3 2004 172.21.1.1
ip host 2950-sw2 2005 172.21.1.1
ip host 2600-2 2009 172.21.1.1
ip host 2950-sw1 2006 172.21.1.1
ip host pix-1 2016 172.21.1.1
!
!
!
!
interface Loopback0
ip address 172.21.1.1 255.0.0.0
!
interface Loopback1
no ip address
!
interface Ethernet0
ip address 171.123.1.1 255.255.255.0
no ip mroute-cache
!
interface Serial0
no ip address
no ip split-horizon
encapsulation frame-relay
no ip mroute-cache
no fair-queue
!
interface Serial0.102 multipoint
ip address 191.168.123.1 255.255.255.0
frame-relay map ip 191.168.123.2 102 broadcast
frame-relay map ip 191.168.123.3 103 broadcast
!
interface Serial0.112 point-to-point
ip address 191.168.12.1 255.255.255.0
frame-relay interface-dlci 112
!
interface Serial1
no ip address
shutdown
!
router eigrp 10
network 171.123.1.0 0.0.0.255
network 191.168.12.0 0.0.0.255
network 191.168.123.0 0.0.0.255
auto-summary
!
ip default-gateway 171.55.31.1
no ip http server
ip classless
!
!
!
alias exec c copy run start
!
line con 0
exec-timeout 0 0
logging synchronous
transport preferred telnet
line 1 16
session-timeout 20
exec-timeout 0 0
no exec
transport input telnet
line aux 0
logging synchronous
transport preferred telnet
transport input all
speed 38400
flowcontrol hardware
line vty 0 4
exec-timeout 60 0
password 7 13061E01080344
logging synchronous
login
!
end
Solved! Go to Solution.
06-27-2012 02:43 AM
Hi,
1)on the FR switch, no need for any routing protocol as well as FR mappings, this is just a switch.
But it is not configured as a FR relay switch in the output config you posted ? where is this part of the config
2) on R1: on the multipoint subnet you must have s0.103 pointing to R3 and not s0.102 which is already pointing to R2
if you want to use a FR switch
3) split-horizon problem symptom is the spokes see the hub routes but not the other spokes routes so on the hub which should be R1 you have to disable split-horizon for the EIGRP process with the no ip split-horizon eigrp x interface command.
Regards.
Alain.
Don't forget to rate helpful posts.
06-26-2012 04:09 AM
sorry its like this but couldnt paste all in 1 post for some reason#
R2
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname BERLIN
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$M.5O$tU0pO7ImmP4A/X9Yj1K5y/
!
no aaa new-model
!
resource policy
!
ip cef
!
!
!
!
no ip domain lookup
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0
no ip address
encapsulation frame-relay
no fair-queue
no dce-terminal-timing-enable
!
interface Serial0/0.201 multipoint
ip address 191.168.123.2 255.255.255.0
frame-relay map ip 191.168.123.1 201 broadcast
frame-relay map ip 191.168.123.3 201 broadcast
!
interface Serial0/0.211 point-to-point
ip address 191.168.12.2 255.255.255.0
frame-relay interface-dlci 211
!
router eigrp 10
network 191.168.12.0 0.0.0.255
network 191.168.123.0 0.0.0.255
auto-summary
!
!
ip http server
!
!
!
control-plane
!
banner login
C
*****************************************************
!!!!!!!!!!GET OFF MY FUCKIN ROUTER OR U DIE!!!!!!!!!!
*****************************************************
alias exec c copy run start
!
line con 0
exec-timeout 0 0
password 7 0822455D0A16
logging synchronous
login
line aux 0
line vty 0 4
exec-timeout 0 0
password 7 01100F175804
logging synchronous
login
!
!
end
06-26-2012 04:11 AM
!
version 11.2
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname STOCKHOLM
!
enable secret 5 $1$cK6v$GLqiVXDPgi2Kuz5hPbu7M.
!
ip subnet-zero
no ip domain-lookup
!
interface Ethernet0
ip address 194.111.0.1 255.255.255.0
!
interface Serial0
no ip address
encapsulation frame-relay
!
interface Serial0.301 multipoint
ip address 191.168.123.3 255.255.255.0
frame-relay map ip 191.168.123.1 301 broadcast
frame-relay map ip 191.168.123.2 301 broadcast
!
interface Serial1
no ip address
shutdown
!
router eigrp 10
network 191.168.0.0
network 194.111.0.0
!
ip http server
ip classless
banner login
C
*****************************************************
*****************************************************
alias exec c copy run start
!
line con 0
exec-timeout 0 0
password 7 05080F1C2243
logging synchronous
login
line 1 16
line aux 0
line vty 0 4
exec-timeout 0 0
password 7 030752180500
logging synchronous
login
!
end
06-26-2012 04:12 AM
raame-relay switch
!
version 11.2
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname STOCKHOLM
!
enable secret 5 $1$cK6v$GLqiVXDPgi2Kuz5hPbu7M.
!
ip subnet-zero
no ip domain-lookup
!
interface Ethernet0
ip address 194.111.0.1 255.255.255.0
!
interface Serial0
no ip address
encapsulation frame-relay
!
interface Serial0.301 multipoint
ip address 191.168.123.3 255.255.255.0
frame-relay map ip 191.168.123.1 301 broadcast
frame-relay map ip 191.168.123.2 301 broadcast
!
interface Serial1
no ip address
shutdown
!
router eigrp 10
network 191.168.0.0
network 194.111.0.0
!
ip http server
ip classless
banner login
C
*****************************************************
!!!!!!!!!!GET OFF MY ROUTER OR U DIE!!!!!!!!!!
*****************************************************
alias exec c copy run start
!
line con 0
exec-timeout 0 0
password 7 05080F1C2243
logging synchronous
login
line 1 16
line aux 0
line vty 0 4
exec-timeout 0 0
password 7 030752180500
logging synchronous
login
!
end
any ideas thanks
thanks chris
06-26-2012 04:29 AM
Hi,
you surely have a problem with EIGRP split-horizon( but I just took a quick look at the configs and diagram).
Can you post output of sh ip route eigrp on all routers as well as sh ip eigrp neigh
Regards.
Alain .
Don't forget to rate helpful posts.
06-27-2012 12:12 AM
hi cadet thanks for your reply,ok nso ill tell u wot ive done first then post the outputs,after your reply i looked in each routing tables and the route was there but as a summarised route sh i checked sh ip protocols and on all 3 routers i had not done no auto-summarisation,so added the command to all 3 router but not thr fr switch(do i need to??do i even need to enable eigrp on fr switch ??as i have)now some rout tables sh the route and some dont heres outputs
tewys-comm-server#sh ip route eigrp
D 192.168.10.0/24 [90/2198016] via 171.123.1.2, 00:19:57, Ethernet0
172.30.0.0/24 is subnetted, 9 subnets
D 172.30.2.0 [90/409600] via 171.123.1.2, 00:19:57, Ethernet0
D 172.30.3.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.0.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.1.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.6.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.7.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.4.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.5.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 172.30.8.0 [90/409600] via 171.123.1.2, 00:19:58, Ethernet0
D 192.168.20.0/24 [90/2198016] via 171.123.1.2, 00:19:58, Ethernet0
D 192.168.1.0/24 [90/2198016] via 171.123.1.2, 00:19:58, Ethernet0
D 194.111.0.0/24 [90/2195456] via 191.168.123.3, 00:09:38, Serial0.102
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
D 192.168.2.0/24 [90/2195456] via 171.123.1.2, 00:19:59, Ethernet0
D 192.168.2.1/32 [90/2195456] via 171.123.1.2, 00:19:59, Ethernet0
R1
tewys-comm-server#sh ip eigrp neighbor
IP-EIGRP neighbors for process 10
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
2 191.168.123.3 Se0.102 139 00:10:49 1464 5000 0 16
3 191.168.123.2 Se0.102 129 00:20:31 101 606 0 23
1 171.123.1.2 Et0 12 00:21:09 20 200 0 23
0 191.168.12.2 Se0.112 11 00:21:09 22 200 0 22
BERLIN#sh ip route eigrp
171.123.0.0/24 is subnetted, 1 subnets
D 171.123.1.0 [90/2195456] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2195456] via 191.168.12.1, 00:15:13, Serial0/0.211
D 192.168.10.0/24 [90/2710016] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2710016] via 191.168.12.1, 00:15:13, Serial0/0.211
172.30.0.0/24 is subnetted, 9 subnets
D 172.30.2.0 [90/2323456] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:13, Serial0/0.211
D 172.30.3.0 [90/2323456] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:13, Serial0/0.211
D 172.30.0.0 [90/2323456] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:13, Serial0/0.211
D 172.30.1.0 [90/2323456] via 191.168.123.1, 00:15:13, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:13, Serial0/0.211
D 172.30.6.0 [90/2323456] via 191.168.123.1, 00:15:14, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:14, Serial0/0.211
D 172.30.7.0 [90/2323456] via 191.168.123.1, 00:15:14, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:14, Serial0/0.211
D 172.30.4.0 [90/2323456] via 191.168.123.1, 00:15:14, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:14, Serial0/0.211
D 172.30.5.0 [90/2323456] via 191.168.123.1, 00:15:14, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:14, Serial0/0.211
D 172.30.8.0 [90/2323456] via 191.168.123.1, 00:15:14, Serial0/0.201
[90/2323456] via 191.168.12.1, 00:15:14, Serial0/0.211
D 192.168.20.0/24 [90/2710016] via 191.168.123.1, 00:15:31, Serial0/0.201
[90/2710016] via 191.168.12.1, 00:15:31, Serial0/0.211
D 192.168.1.0/24 [90/2710016] via 191.168.123.1, 00:15:32, Serial0/0.201
[90/2710016] via 191.168.12.1, 00:15:32, Serial0/0.211
D 194.111.0.0/24 [90/2707456] via 191.168.12.1, 00:06:09, Serial0/0.211
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
D 192.168.2.0/24 [90/2707456] via 191.168.123.1, 00:15:34, Serial0/0.201
[90/2707456] via 191.168.12.1, 00:15:34, Serial0/0.211
D 192.168.2.1/32 [90/2707456] via 191.168.123.1, 00:15:35, Serial0/0.201
[90/2707456] via 191.168.12.1, 00:15:35, Serial0/0.211
R2
BERLIN#sh ip eigrp neighbor
IP-EIGRP neighbors for process 10
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
1 191.168.123.1 Se0/0.201 166 00:17:04 165 990 0 29
0 191.168.12.1 Se0/0.211 12 00:17:59 25 200 0 28
R3
STOCKHOLM#sh ip route eigrp
191.168.0.0/24 is subnetted, 2 subnets
D 191.168.12.0 [90/2681856] via 191.168.123.1, 00:01:29, Serial0.301
D 192.168.10.0/24 [90/2710016] via 191.168.123.1, 00:01:29, Serial0.301
D 192.168.1.0/24 [90/2710016] via 191.168.123.1, 00:01:29, Serial0.301
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
D 192.168.2.0/24 [90/2707456] via 191.168.123.1, 00:01:29, Serial0.301
D 192.168.2.1/32 [90/2707456] via 191.168.123.1, 00:01:29, Serial0.301
D 192.168.20.0/24 [90/2710016] via 191.168.123.1, 00:01:29, Serial0.301
172.30.0.0/24 is subnetted, 9 subnets
D 172.30.2.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.3.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.0.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.1.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.6.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.7.0 [90/2323456] via 191.168.123.1, 00:01:29, Serial0.301
D 172.30.4.0 [90/2323456] via 191.168.123.1, 00:01:30, Serial0.301
D 172.30.5.0 [90/2323456] via 191.168.123.1, 00:01:30, Serial0.301
D 172.30.8.0 [90/2323456] via 191.168.123.1, 00:01:30, Serial0.301
171.123.0.0/24 is subnetted, 1 subnets
D 171.123.1.0 [90/2195456] via 191.168.123.1, 00:01:30, Serial0.301
STOCKHOLM#sh ip eigrp neigh
IP-EIGRP neighbors for process 10
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
1 191.168.123.1 Se0.301 125 00:03:39 76 456 0 29
0 194.111.0.2 Et0 14 00:04:00 28 200 0 9
also do i need to do clock rate on the frame-relay serial links????
thanks again for your help sorry it took so long for me to reply
thanks chris
06-27-2012 02:43 AM
Hi,
1)on the FR switch, no need for any routing protocol as well as FR mappings, this is just a switch.
But it is not configured as a FR relay switch in the output config you posted ? where is this part of the config
2) on R1: on the multipoint subnet you must have s0.103 pointing to R3 and not s0.102 which is already pointing to R2
if you want to use a FR switch
3) split-horizon problem symptom is the spokes see the hub routes but not the other spokes routes so on the hub which should be R1 you have to disable split-horizon for the EIGRP process with the no ip split-horizon eigrp x interface command.
Regards.
Alain.
Don't forget to rate helpful posts.
06-27-2012 05:41 AM
hi alain thanks for your reply
1)not sure where confiq gone did do the frame-relay switching command and also did frame-relay routes will check this out and get back to u
2)will check this and get back to u
3)ah i only did no ip split horizon command will change the command
thanks for all your help
chris
06-27-2012 10:07 AM
hi alain when i looked on R1 the commands for split horizon was for the eigrp process so must of missed a bit off while copying and the frame relay switch was the whole wrong sh run not sure why i posted stockholm twice lol so the fr switch has all the right config,it was no 2 as soon as i did what u said i could ping accross,thanks for your help
chris
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: