Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

frame relay

since I reconfiguring frame realy switch ..

R1 can ping r2 and r3

R2 can ping r1

r3 can ping r1

r2 can not ping r3

r3 can not ping r2

frame-switch#sho frame-relay route

Input Intf Input Dlci Output Intf Output Dlci Status

Serial1/1 122 Serial1/2 221 active

Serial1/1 123 Serial1/3 321 active

Serial1/2 221 Serial1/1 122 active

Serial1/3 321 Serial1/1 123 active

===================================

interface Serial1/1

no ip address

encapsulation frame-relay

logging event subif-link-status

logging event dlci-status-change

clock rate 56000

no frame-relay inverse-arp

frame-relay intf-type dce

frame-relay route 122 interface Serial1/2 221

frame-relay route 123 interface Serial1/3 321

!

interface Serial1/2

no ip address

encapsulation frame-relay

logging event subif-link-status

logging event dlci-status-change

clock rate 56000

no frame-relay inverse-arp

frame-relay intf-type dce

frame-relay route 221 interface Serial1/1 122

!

interface Serial1/3

no ip address

encapsulation frame-relay

logging event subif-link-status

logging event dlci-status-change

clock rate 56000

no frame-relay inverse-arp

frame-relay intf-type dce

frame-relay route 321 interface Serial1/1 123

====================================

6 REPLIES
VIP Super Bronze

Re: frame relay

Is r1 the hub and r2 and r3 are the spokes? If yes, are you running any dynamic routing protocols? If no, you need a static route from r2 poining to r1 and also static route from r3 pointing to r1.

HTH

Reza

New Member

Re: frame relay

Reza,

That is correct R1 is Hub r2 and r3 are the spokes.. no dynamic routing protocols ..

R2(config)#ip route 172.12.123.2 255.255.255.0 172.12.123.1

%Inconsistent address and mask

R3(config)#ip route 172.12.123.3 255.255.255.0 172.12.123.1

%Inconsistent address and mask

I tried that and I get and error

Thanks Resa

VIP Super Bronze

Re: frame relay

You need to point to the network no to the hose like:

ip route 172.12.123.0 255.255.255.0 172.12.123.1

I attached an example for your routers

HTH

Reza

VIP Super Bronze

Re: frame relay

correction

You need to point to the network not to the host

New Member

Re: frame relay

still not working RESA,

here is my topology, i went to r2 and added

ip route 172.12.123.0 255.255.255.0 172.12.123.1

and on r3

ip route 172.12.123.0 255.255.255.0 172.12.123.1

am I doing something wrong . is my frame relay config correct...

Thanks

Cisco Employee

Re: frame relay

Hi,

Are you using frame-relay inverse-arp betwen hub and spoke?.

If you use frame relay inverse-arp, try static host entry as below,

R2:

ip route 172.12.123.3 255.255.255.255 172.12.123.1

R3:

ip route 172.12.123.2 255.255.255.255 172.12.123.1

If you have static mapping, configure mapping for spoke pointing to your hub DLCI as below,

R2:

interface

frame-relay map ip 172.12.123.1 broadcast

frame-relay map ip 172.12.123.3

R3:

frame-relay map ip 172.12.123.1 broadcast

frame-relay map ip 172.12.123.2

If it doesnt work, Please post the config @ hub and spoke routers as well.

HTH,

Nagendra

310
Views
9
Helpful
6
Replies