02-11-2012 04:05 AM - edited 03-04-2019 03:13 PM
Hi
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.
I'm trying to setup PPPoE with dynamic IP
Followed CISCO's documentations but the commands used were not recognized by the router. Any simple working config for me to follow will be enough.
I'll appreciate any help. Thanks a lot!
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
!
hostname router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
!
!
ip source-route
!
!
!
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
!
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server x.x.x.x x.x.x.x.x
lease 0 2
!
!
ip cef
no ipv6 cef
!
!
license udi pid CISCO887VA-K9 sn FGLxxxxxxx
!
!
!
!
!
controller VDSL 0
!
ip ftp username cisco
ip ftp password cisco
!
!
!
!
!
!
!
interface Ethernet0
pppoe enable group global
pppoe-client dial-pool-number 1
no ip address
shutdown
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip directed-broadcast
ip virtual-reassembly in
ip tcp adjust-mss 1452
!
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
ppp pap sent-username xxxx password 0 xxxx
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
!
ip access-list standard 1
permit 10.0.0.0 0.0.0.255
no cdp run
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
transport input all
!
end
07-13-2014 12:17 PM
Try to check with your ISP the modem string to use for VDSL
and some ISP support direct dhcp on Ethernet0 without PPPoE.
An equivalent config is working for me in Switzerland with Swisscom.
N.B. "modem" under VDSL controller is enable using service internal !
!
service internal
!
controller VDSL 0
operating mode vdsl2
modem co5
!
ip source-route
ip cef
!
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
!
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server 8.8.8.8
lease 0 2
!
interface Ethernet0
ip address dhcp
ip nat outside
!
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
!
ip nat inside source list 23 interface Ethernet0 overload
!
access-list 23 permit 10.0.0.0 0.0.0.255
!
end
07-20-2014 03:55 PM
i think you may issue no shutdown for ethernet 0 as well
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide