hi yesterday i have a big headache triying to connect a E1 (its a full duplex 2 mbps link) with this modem: PairGain HDSL HiGain ETSI with a Cisco 1841 for a friend in Mexico, it was like impossible for me to accomplish that it was really ftrustrating, i cant ping my serial interfase from the ethernet interface of the cisco, i cant test if the PairGain were able to work fine, i dont know if the PairGain has a console access as the cisco console for administration, configuring or testing suite. I need an advice of how can i do it guys.
Thanks in advance and i attach here my config file:
----------------------
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname EHVGEM
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 10 log
security passwords min-length 6
logging buffered 4096 debugging
logging console critical
enable secret xxxx
enable password xxxx
!
aaa new-model
!
!
aaa authentication login local_auth local
!
aaa session-id common
!
resource policy
!
clock timezone PCTime -7
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
no ip source-route
no ip gratuitous-arps
ip cef
!
!
!
!
no ip bootp server
no ip domain lookup
ip domain name yourdomain.com
ip name-server 200.x.x.1
ip name-server 200.x.x.1
login block-for 3 attempts 3 within 3
username xxx privilege 15 secret xxxx
!
!
!
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 200.130.x.x.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
speed auto
half-duplex
no mop enabled
!
interface FastEthernet0/1
ip address 192.168.101.210 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
duplex auto
speed auto
no mop enabled
!
interface Serial0/0/0
ip address 200.23.x.x.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
clock rate 2000000
!
router rip
redistribute connected
network 10.0.0.0
network 200.x.101.0
network 200.x.237.0
!
ip route 0.0.0.0 0.x.x.x.23.251.201
!
ip http server
ip http authentication local
ip http timeout-policy idle 5 life 86400 requests 10000
!
ip access-list extended autosec_complete_bogon
etc. etc......
permit ip any any
!
logging trap debugging
logging facility local2
access-list 100 permit udp any any eq bootpc
access-list compiled
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
banner login C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device. This
feature requires the one time use, initial credentials, of username "cisco"
with password "cisco".
Please change these publicly known initial credentials through SDM or IOS CLI.
Here's the Cisco IOS command:
no username cisco
NOTE: Please add a new username to be able to launch SDM for router management.
For more information about SDM please follow the instructions in the QUICK
START GUIDE for your router or at
http://www.cisco.com/go/sdm
-----------------------------------------------------------------------
banner motd C EHV-GEM Authorized Use
!
line con 0
exec-timeout 5 0
login authentication local_auth
transport output telnet
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
line vty 0 4
privilege level 15
password xxxx
login authentication local_auth
transport input telnet
line vty 5 15
privilege level 15
password xxxx
login authentication local_auth
transport input telnet
!
scheduler allocate 20000 1000
end
--------------------
