01-25-2013 02:52 PM - edited 03-04-2019 06:50 PM
hi there,
y have a lttle problem to cofigure a ADSL2+ Conexion in an 1941 router.
line protocol are up but didn't have ip adresse in my interface...
Current configuration : 1986 bytes
!
! Last configuration change at 22:32:07 UTC Fri Jan 25 2013
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname XXXXXXXXXXXX
!
boot-start-marker
boot-end-marker
!
!
enable password 7 063656356B49394B4F
!
no aaa new-model
!
no ipv6 cef
ip source-route
ip cef
!
!
!
!
!
multilink bundle-name authenticated
!
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol l2tp
!
crypto pki token default removal timeout 0
!
!
!
!
!
!
controller VDSL 0/1/0
operating mode adsl2+
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 192.168.9.250 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 192.168.1.253 255.255.255.0
duplex auto
speed auto
!
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
pvc 8/81
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Ethernet0/1/0
no ip address
shutdown
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication chap pap callin
ppp chap hostname uribej
ppp chap password 7 055A545C75191849
ppp pap sent-username uribej password 7 11584B5643475D4C
!
router rip
version 2
network 192.168.1.0
network 192.168.9.0
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit 192.168.9.0 0.0.0.255
access-list 1 remark "Access liste por el NAT (Internet)"
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password 7 107E500D2210225946
login
transport input all
!
scheduler allocate 20000 1000
end
show ip interface brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/0 192.168.9.250 YES NVRAM up up
GigabitEthernet0/1 192.168.1.253 YES NVRAM down down
ATM0/1/0 unassigned YES unset down down
Ethernet0/1/0 unassigned YES unset administratively down down
Dialer1 unassigned YES manual up up
NVI0 192.168.9.250 YES unset up up
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset down down
i don't know how i can find the probleme, and debug's comandes no show me anything.
I'im located in mexico, and use TELMEX provider.
the conexion is an ADSL2+, and prvider's box conect them with PPPoE...
sorry for my bad english.
thank's for your help,
01-31-2013 11:10 PM
Start with "show controllers vdsl".
02-11-2013 10:48 AM
Hello and thank you for your response,
Apparently the line is detected by the controller…
Before comment, I try to put the card in "automatic"
And apparently this line doesn’t work in ADSL2+...
###############################
Router#show controllers vdsL 0/1/0
Controller VDSL 0/1/0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'ALCB'
Chip Vendor Specific: 0x0000 0x0000
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FOC16454FN7 1941/K9 15.1(4)M
Serial Number Far:
Modem Version Near: 15.1(4)M
Modem Version Far: 0x0000
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.992.1 (ADSL) Annex A
TC Mode: ATM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
Line Attenuation: 19.0 dB 14.0 dB
Signal Attenuation: 19.0 dB 0.0 dB
Noise Margin: 30.7 dB 28.0 dB
Attainable Rate: 10064 kbits/s 1156 kbits/s
Actual Power: 17.1 dBm 11.9 dBm
Total FECS: 0 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 0 0
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
Bit swap: 0 0
Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110506_1916-4.02L.03.A2pv6C032b.d23i
Modem PHY Version: A2pv6C032b.d23i
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 2048 0 384
Previous Speed: 0 0 0 0
Total Cells: 0 4602427 0 0
User Cells: 0 0 0 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 0.25 0.00 0.25
Actual INP: 0.00 0.00 0.00 0.00
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
02-12-2013 03:58 PM
Hello!!
Did you tryed with this resolve?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide