Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

How to configure two 6506’s for Redundancy.

How to configure two 6506’s for Redundancy.

I have two 6506s with one “WS-X6K-SUP2-2GE w : 5.1” pre device. I would like to set these two devices in a redundancy topology, meaning if the primary 6506 failed the secondary (standby) 6506 will take total identity of the failed 6506, including moving all the running configuration information.

Can someone please tell me the best way to make this happen and/or point me in the right direction so that I can research?

SHOW MOD IS THE SAME ON BOTH DEVICES:

WS-C6506 Software, Version NmpSW: 8.2(2)

Copyright (c) 1995-2004 by Cisco Systems

NMP S/W compiled on Apr  7 2004, 12:09:03

System Bootstrap Version: 7.1(1)

System Web Interface Version: Engine Version: 5.3.4 ADP Device: Cat6000 ADP Version: 5.0 ADK: 40

System Boot Image File is 'bootflash:cat6000-sup2cvk9.8-2-2.bin'

System Configuration register is 0x2102

Hardware Version: 3.0  Model: WS-C6506  Serial #: SAL08332DYP

PS1  Module: WS-CAC-1300W    Serial #: ABC08232025

PS2  Module: WS-CAC-1300W    Serial #: ABC08232027

Mod Port Model               Serial #    Versions

--- ---- ------------------- ----------- --------------------------------------

1   2    WS-X6K-SUP2-2GE     SAL083742B0 Hw : 5.1 

                                         Fw : 7.1(1)

                                         Fw1: 6.1(3)

                                         Sw : 8.2(2)

                                         Sw1: 8.2(2)

         WS-F6K-PFC2         SAL08373W54 Hw : 3.5 

                                         Sw :

         WS-X6K-SUP2-2GE     SAL083742B0 Hw : 5.1

                                         Sw :

2   16   WS-X6516A-GBIC      SAL08342XAE Hw : 4.1

                                         Fw : 7.2(1)

                                         Sw : 8.2(2)

3   48   WS-X6148-45AF       SAL08186FS3 Hw : 1.0

                                         Fw : 5.4(2)

                                         Sw : 8.2(2)

         WS-F6K-FE48-AF      SAD08250552 Hw : 1.2

                                         Sw : 8.2(226)

4   48   WS-X6548-GE-TX      SAL1126SAPN Hw : 11.1

                                         Fw : 7.2(1)

                                         Sw : 8.2(2)

15  1    WS-F6K-MSFC2        SAL08342LA6 Hw : 2.8

                                         Fw : 12.1(22)E2

                                         Sw : 12.1(22)E2

       DRAM                    FLASH                   NVRAM

Module Total   Used    Free    Total   Used    Free    Total Used  Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1      262144K  82831K 179313K  32768K  14484K  18284K  512K  306K  206K

2 REPLIES
VIP Super Bronze

Re: How to configure two 6506’s for Redundancy.

Hello lawrence,

If you had 6500-E, you could pair them together and create a VSS bundle similar to 3750 stacking, but unfortunately you have none E 6500, so that is not poosible.

You also have to have the right sup to do VSS.(Sup-720-VS)

HTH

Reza

New Member

Re: How to configure two 6506’s for Redundancy.

Thanks you

364
Views
0
Helpful
2
Replies