How to install IOS to cisco 881-w

jurijs_visockis · ‎02-09-2012

Hi. I formatted flash and now I need to install IOS .

I know than I have to do it using TFTPD, but I cant connect my PC and cisco.

On cisco throught console in putty I wrote :

rommon 1 > set

rommon 2 > IP_ADDRESS=10.10.10.2

rommon 3 > IP_SUBNET_MASK=255.255.255.0

in pc local area connection

10.10.10.3 255.255.255.0

try to ping and no signal.

How to connect cisco and pc

Leo Laohoo · ‎02-09-2012

That's not complete.

Where's your TFTP server IP address?

Where's your default gateway IP address?

Where's the IOS file?

Cory Dryden · ‎02-09-2012

Straight from CCNA command guide. Once in rommon mode type following commands.

IP_ADDRESS=X.X.X.X

IP_SUBNET_MASK=X.X.X.X

DEFAULT_GATEWAY=X.X.X.X

TFTP_SERVER=X.X.X.X

TFTP_FILE=xxxxxxxxxx

tftpdnld

Once done type just the letter i to reload the router.

jurijs_visockis · ‎02-11-2012

Thank`s I did it.

Now I can`t configure WIFI, client didn`t get IP address, there is my access point config

ap#sh run

Building configuration...

Current configuration : 2325 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname ap

!

enable secret 5 $1$dWJ8$Q7gffyWV3kiTNjDBwMvNn/

!

no aaa new-model

!

dot11 syslog

!

dot11 ssid D13VSK

vlan 1

authentication open

authentication key-management wpa

mbssid guest-mode

wpa-psk ascii 0 S13admin

!

username admin privilege 15 secret 5 $1$wNjR$5JBdFPNe4HV/srkkg2M2I1

!

bridge irb

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption vlan 1 mode ciphers aes-ccm tkip

!

broadcast-key vlan 1 change 30

!

ssid D13VSK

!

antenna gain 0

mbssid

station-role root

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

bridge-group 2 spanning-disabled

!

interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting A P with the host router

no ip address

no ip route-cache

!

interface GigabitEthernet0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address dhcp client-id GigabitEthernet0

no ip route-cache

!

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

!

banner login ^CC

% Password change notice.

-----------------------------------------------------------------------

Default username/password setup on AP is cisco/cisco with privilege level 15.

It is strongly suggested that you create a new username with privilege level

15 using the following command for console security.

username privilege 15 secret 0

no username cisco

Replace and with the username and password you want to

use. After you change your username/password you can turn off this message

by configuring "no banner login" and "no banner exec" in privileged mode.

-----------------------------------------------------------------------

^C

!

line con 0

privilege level 15

login local

no activation-character

line vty 0 4

login local

!

cns dhcp

end

Leo Laohoo · ‎02-11-2012

Now I can`t configure WIFI, there is my access point config

You need to be more specific than this!

jurijs_visockis · ‎02-11-2012

This is my router config

CiscoWifi#sh run

Building configuration...

Current configuration : 3956 bytes

!

! Last configuration change at 11:33:28 UTC Sat Feb 11 2012 by admin

! NVRAM config last updated at 11:33:16 UTC Sat Feb 11 2012 by admin

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname CiscoWifi

!

boot-start-marker

boot config flash:router-config

boot-end-marker

!

no logging console

enable secret 5 $1$LOzN$Ti9UiynDabsPapSTqmD.O.

!

aaa new-model

!

aaa session-id common

memory-size iomem 10

crypto pki token default removal timeout 0

!

crypto pki trustpoint TP-self-signed-182589002

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-182589002

revocation-check none

rsakeypair TP-self-signed-182589002

!

crypto pki certificate chain TP-self-signed-182589002

certificate self-signed 01

30820229 30820192 A0030201 02020101 300D0609 2A864886 F70D0101 05050030

30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274

69666963 6174652D 31383235 38393030 32301E17 0D313230 32313131 30313032

365A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F

532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3138 32353839

30303230 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100

C9FD8A23 4BD415F5 C02A81F4 71798DD1 5A577937 A1A3352C 05339EFE 95A667ED

AF95CDE2 047F8E95 14E693AD 7E4D02B4 C98D4C69 A5C15EDD ABEF7C20 387D27E3

48701545 2F9C72E2 6D6816BB 77ECC417 1DB2B09E A0619FA2 64FA8647 A2BDFBED

EB324EF2 FEBC9F81 B60F75CF B89805F8 048909E5 9AF46F4A 1AA42756 B76D7065

02030100 01A35330 51300F06 03551D13 0101FF04 05300301 01FF301F 0603551D

23041830 168014EB 86D0BDBE 8C59FB90 BBA3E6A0 037D254B 48E49530 1D060355

1D0E0416 0414EB86 D0BDBE8C 59FB90BB A3E6A003 7D254B48 E495300D 06092A86

4886F70D 01010505 00038181 0053F16B 0B3656EA F019A12D E91E312E 3D3CE8F2

0C95EF12 35173535 E3EA6242 97825ABD 4C90F487 47A3A2DB 3ACE3867 E4633D2B

23623C2C 7A833E99 B760831F EC208D5D 215CB486 5E8EE68A AE4435C0 1166CB4B

6840C38F EBFFF70E AF5F4FA9 B15A5089 49B3D1F5 FD966D93 C939621D DB605E55

A742BABA 7DA88D79 AD4F8A81 98

quit

!

ip dhcp excluded-address 10.13.10.1 10.13.10.4

ip dhcp excluded-address 10.13.10.201 10.13.10.254

!

ip dhcp pool dhcp1

import all

network 10.13.10.0 255.255.255.0

default-router 10.13.10.1

!

no ip domain lookup

ip domain name daug13vsk.lv

ip cef

no ipv6 cef

!

license udi pid CISCO881W-GN-E-K9 sn FCZ1432900Q

!

username user privilege 15 secret 5 $1$D0mB$ckLG9PDTTeOTjqcgH8jzQ0

username admin privilege 15 secret 5 $1$FbGR$jqb6b1SCdSi7DPTh5Zb5o1

username adm privilege 15 password 7 00374255055F060F01

!

interface FastEthernet0

no ip address

!

interface FastEthernet1

no ip address

!

interface FastEthernet2

no ip address

!

interface FastEthernet3

no ip address

!

interface FastEthernet4

ip address dhcp

ip nat outside

ip virtual-reassembly in

duplex auto

speed auto

!

interface wlan-ap0

description Service module interface to manage the embedded AP

ip unnumbered Vlan1

arp timeout 0

!

interface Wlan-GigabitEthernet0

description Internal switch interface connecting to the embedded AP

switchport mode trunk

no ip address

!

interface Vlan1

ip address 10.13.10.1 255.255.255.0

ip nat inside

ip virtual-reassembly in

!

ip forward-protocol nd

ip http server

ip http authentication local

ip http secure-server

!

ip nat inside source list 1 interface FastEthernet4 overload

ip route 0.0.0.0 0.0.0.0 192.168.1.1 254

!

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.13.10.0 0.0.0.255

!

line con 0

exec-timeout 5 30

password 7 06355E724D4A04100B

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

line vty 0 4

exec-timeout 40 0

logging synchronous

transport input ssh

!

end