Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Cisco Employee

HSRP and GLBP on the same interface

Hi,

As anyone ever configured HSRP and GLBP on the same interface please?

If so, are there any things I need to watch out for please?

Thanks.

2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

Re: HSRP and GLBP on the same interface

Hi,

Please refer this doc...

http://ciscostudy.blogspot.com/2006_02_14_archive.html

Regards,

Imran.

Re: HSRP and GLBP on the same interface

Friend,

I did some test and there is absolutely no problem in defining HSRP and GLBP on the same interface.

have a look at the below config

interface FastEthernet0/0

ip address 10.10.10.2 255.255.255.0

duplex auto

speed auto

glbp 1 ip 10.10.10.100

glbp 1 priority 200

glbp 1 preempt

standby 1 ip 10.10.10.1

standby 1 priority 105

standby 1 preempt

The only problem is that you cannot have the HSRP virtual IP and the GLBP IP as same.

When you try to do that you get an error as mentioned below

R2(config-if)#glbp 1 ip 10.10.10.1

% 10.10.10.1 is assigned to another application on FastEthernet0/0

So in effect, if you want to run GLBP, then your hosts should point to the GLBP IP and if you want to run HSRP point to the HSRP virtual IP

HTH, rate if it does

Narayan

6 REPLIES
Cisco Employee

Re: HSRP and GLBP on the same interface

Hi,

Thanks for the very quick reply. Unfortunately the other thread doesn't answer the question definitively. They think it will work (I think it will as well), but are not 100% sure.

The configuration guide doesn't state that enabling HSRP/GLBP will disable the other, but it also doesn't explicitly state that it doesn't either.

New Member

Re: HSRP and GLBP on the same interface

Hi,

Please refer this doc...

http://ciscostudy.blogspot.com/2006_02_14_archive.html

Regards,

Imran.

Re: HSRP and GLBP on the same interface

Friend,

I did some test and there is absolutely no problem in defining HSRP and GLBP on the same interface.

have a look at the below config

interface FastEthernet0/0

ip address 10.10.10.2 255.255.255.0

duplex auto

speed auto

glbp 1 ip 10.10.10.100

glbp 1 priority 200

glbp 1 preempt

standby 1 ip 10.10.10.1

standby 1 priority 105

standby 1 preempt

The only problem is that you cannot have the HSRP virtual IP and the GLBP IP as same.

When you try to do that you get an error as mentioned below

R2(config-if)#glbp 1 ip 10.10.10.1

% 10.10.10.1 is assigned to another application on FastEthernet0/0

So in effect, if you want to run GLBP, then your hosts should point to the GLBP IP and if you want to run HSRP point to the HSRP virtual IP

HTH, rate if it does

Narayan

Cisco Employee

Re: HSRP and GLBP on the same interface

Hi Narayan,

Thanks for much for trying this out for me, I really appreciate that.

This is exactly what I was after, so thanks again!!!

Cisco Employee

Re: HSRP and GLBP on the same interface

perfect, that's exactly what I was looking for. Thanks for taking the time to reply.

622
Views
0
Helpful
6
Replies