Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1076
Views
0
Helpful
5
Replies

HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

georgd
Level 1
Level 1

‎03-21-2008 02:12 AM - edited ‎03-03-2019 09:13 PM

Hi all

I have cisco 1841 router with hwic-2shdsl card. IOS c1841-advipservicesk9-mz.124-15.T3.bin

I need to connect Zyxel IES-1000+SAM1008 in mode 4wired.

Config on Cisco:

controller SHDSL 0/0/0

dsl-group 0 pairs 0, 1

shdsl annex B

shdsl rate auto

Config on Zyxel (used port 3 and 4)

set profile 2304B 2240 192

set port 3 2304B

set port 4 2304B

set nwirec 4w kassadepo 2

enable port 1 2 4 8

On Cisco: sh controller shdsl

...

SHDSL wire-pair (0) is in DSL DOWN state

Termination: CPE, line mode: 4-wire, Annex-B

Line coding: 16-TCPAM, configured/actual rate: AUTO/0 kbps

CONNECT state: MAIN_PRE_ACT, cond: GHS_TRANSFER, reason: ERR_NONE

...

SHDSL wire-pair (1) is in DSL DOWN state

Termination: CPE, line mode: 4-wire, Annex-B

Line coding: 16-TCPAM, configured/actual rate: AUTO/0 kbps

CONNECT state: MAIN_INIT, cond: NONE, reason: ERR_NONE

On Zyxel: list nwire

N-wire configuration:

Group name Mode Group# Bundled ports

-------------------------------+-------------+--------+--------------

kassadepo 4-wire STU-C group2 3-4

list ports

Port Speed (Kbps) Mode Bonding PSD region State

Cmax/Cmin/Act

----+---------------+---------------+--------+-----------+--------------

3 2240/ 192/ - 4-wireC slave No annexB Disabled/Down

4 2240/ 192/ - 4-wireC master No annexB Enabled /Down

Can anyone help me?

Labels:
0 Helpful
5 Replies 5

georgd
Level 1
Level 1

‎03-23-2008 10:31 PM

Can anyone help me?

0 Helpful

georgd
Level 1
Level 1
In response to georgd

‎03-25-2008 08:01 AM

Any idea?

0 Helpful

Pavel Bykov
Level 5
Level 5

‎04-01-2008 03:29 AM

try "debug xdsl driver" on Cisco side

0 Helpful

georgd
Level 1
Level 1
In response to Pavel Bykov

‎04-01-2008 05:30 AM

sh deb

HWIC-SHDSL debugs:

HWIC-SHDSL DSL events debugging is on

HWIC-SHDSL firmware events logging debugging is on

KRO-OK-2(config-controller)# dsl-group 0 pairs 0, 1

KRO-OK-2(config-controller-dsl-group)#no shut

KRO-OK-2(config-controller-dsl-group)#

*Mar 13 14:49:17.859: shdsl 0/0/0, grp(0), IPC msg dump:

*Mar 13 14:49:17.859: 0x1 0x0 0xE 0x0 0x2 0x3 0x2 0x0 0x2 0x3 0x24 0x0 0x2 0x0 0xFF 0xFF

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[x]: Process dsl cmd 0 chan_mask 0x9

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DMT[0]: Clock Mode = 0x4

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[0]: Released->SetCfg tr: lincfg

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DMT[3]: Clock Mode = 0x4

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[3]: Released->SetCfg tr: lincfg

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00]: CCT_SHDSL_CMD_SET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00]: CCT_SHDSL_CMD_GET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[03]: CCT_SHDSL_CMD_SET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[03]: CCT_SHDSL_CMD_GET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00] idle

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: CCT[03] idle

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DMT[0]: Rx shdsl ack set cfg, rc 0

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DSM[0]: SetCfg->CfgDnld tr: ack

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DMT[3]: Rx shdsl ack set cfg, rc 0

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DSM[3]: SetCfg->CfgDnld tr: ack

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: CCT_CMD_START_CONFIG

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00] CCT_StartConfigDownload

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: CCT_CMD_START_CONFIG

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03] CCT_StartConfigDownload

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00] configure

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteConfig

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03] configure

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteConfig

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: DMT[0]: Rx ack start config, rc 0

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DSM[0]: CfgDnld->CfgDnld tr: ack

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DMT[3]: Rx ack start config, rc 0

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DSM[3]: CfgDnld->CfgDnld tr: ack

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00] configure

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteConfig

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteSdiIfSettings(FOURWIRE) - if_sel = 0

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[03] configure

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[03]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.999: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteConfig

*Mar 13 14:49:17.999: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteSdiIfSettings(FOURWIRE) - if_sel = 0

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: SCI AUX Msg 0x0002 received (len 1)

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: CCT_MSG_TUNNEL / SCI AUX

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: SCI AUX Msg 0x0002 received (len 1)

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: CCT_MSG_TUNNEL / SCI AUX

0 Helpful

georgd
Level 1
Level 1
In response to georgd

‎04-07-2008 02:22 AM

Can anyone help me?

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card