Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

Hi all

I have cisco 1841 router with hwic-2shdsl card. IOS c1841-advipservicesk9-mz.124-15.T3.bin

I need to connect Zyxel IES-1000+SAM1008 in mode 4wired.

Config on Cisco:

controller SHDSL 0/0/0

dsl-group 0 pairs 0, 1

shdsl annex B

shdsl rate auto

Config on Zyxel (used port 3 and 4)

set profile 2304B 2240 192

set port 3 2304B

set port 4 2304B

set nwirec 4w kassadepo 2

enable port 1 2 4 8

On Cisco: sh controller shdsl

...

SHDSL wire-pair (0) is in DSL DOWN state

Termination: CPE, line mode: 4-wire, Annex-B

Line coding: 16-TCPAM, configured/actual rate: AUTO/0 kbps

CONNECT state: MAIN_PRE_ACT, cond: GHS_TRANSFER, reason: ERR_NONE

...

SHDSL wire-pair (1) is in DSL DOWN state

Termination: CPE, line mode: 4-wire, Annex-B

Line coding: 16-TCPAM, configured/actual rate: AUTO/0 kbps

CONNECT state: MAIN_INIT, cond: NONE, reason: ERR_NONE

On Zyxel: list nwire

N-wire configuration:

Group name Mode Group# Bundled ports

-------------------------------+-------------+--------+--------------

kassadepo 4-wire STU-C group2 3-4

list ports

Port Speed (Kbps) Mode Bonding PSD region State

Cmax/Cmin/Act

----+---------------+---------------+--------+-----------+--------------

3 2240/ 192/ - 4-wireC slave No annexB Disabled/Down

4 2240/ 192/ - 4-wireC master No annexB Enabled /Down

Can anyone help me?

5 REPLIES
New Member

Re: HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

Can anyone help me?

New Member

Re: HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

Any idea?

Silver

Re: HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

try "debug xdsl driver" on Cisco side

New Member

Re: HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

sh deb

HWIC-SHDSL debugs:

HWIC-SHDSL DSL events debugging is on

HWIC-SHDSL firmware events logging debugging is on

KRO-OK-2(config-controller)# dsl-group 0 pairs 0, 1

KRO-OK-2(config-controller-dsl-group)#no shut

KRO-OK-2(config-controller-dsl-group)#

*Mar 13 14:49:17.859: shdsl 0/0/0, grp(0), IPC msg dump:

*Mar 13 14:49:17.859: 0x1 0x0 0xE 0x0 0x2 0x3 0x2 0x0 0x2 0x3 0x24 0x0 0x2 0x0 0xFF 0xFF

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[x]: Process dsl cmd 0 chan_mask 0x9

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DMT[0]: Clock Mode = 0x4

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[0]: Released->SetCfg tr: lincfg

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DMT[3]: Clock Mode = 0x4

*Mar 13 14:49:17.891: SHDSL0/0/0 FW MSG: DSM[3]: Released->SetCfg tr: lincfg

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00]: CCT_SHDSL_CMD_SET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00]: CCT_SHDSL_CMD_GET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[03]: CCT_SHDSL_CMD_SET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[03]: CCT_SHDSL_CMD_GET_CONFIG

*Mar 13 14:49:17.895: SHDSL0/0/0 FW MSG: CCT[00] idle

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: CCT[03] idle

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DMT[0]: Rx shdsl ack set cfg, rc 0

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DSM[0]: SetCfg->CfgDnld tr: ack

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DMT[3]: Rx shdsl ack set cfg, rc 0

*Mar 13 14:49:17.899: SHDSL0/0/0 FW MSG: DSM[3]: SetCfg->CfgDnld tr: ack

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: CCT_CMD_START_CONFIG

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00] CCT_StartConfigDownload

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: CCT_CMD_START_CONFIG

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03] CCT_StartConfigDownload

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00] configure

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteConfig

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03] configure

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteConfig

*Mar 13 14:49:17.947: SHDSL0/0/0 FW MSG: DMT[0]: Rx ack start config, rc 0

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DSM[0]: CfgDnld->CfgDnld tr: ack

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DMT[3]: Rx ack start config, rc 0

*Mar 13 14:49:17.951: SHDSL0/0/0 FW MSG: DSM[3]: CfgDnld->CfgDnld tr: ack

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00] configure

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteConfig

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[00]: SDFE4_WriteSdiIfSettings(FOURWIRE) - if_sel = 0

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[03] configure

*Mar 13 14:49:17.995: SHDSL0/0/0 FW MSG: CCT[03]: SOC16_WalkTroughTable 0

*Mar 13 14:49:17.999: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteConfig

*Mar 13 14:49:17.999: SHDSL0/0/0 FW MSG: CCT[03]: SDFE4_WriteSdiIfSettings(FOURWIRE) - if_sel = 0

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: SCI AUX Msg 0x0002 received (len 1)

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: CCT_MSG_TUNNEL / SCI AUX

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: SCI AUX Msg 0x0002 received (len 1)

*Mar 13 14:49:18.003: SHDSL0/0/0 FW MSG: CCT[00]: CCT_MSG_TUNNEL / SCI AUX

New Member

Re: HWIC-2SHDSL 4-wire connect to Zyxel IES-1000+SAM1008

Can anyone help me?

724
Views
0
Helpful
5
Replies