Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

I can not reach a PPPoE client from the outside

I have a PPPoE server on the router. The PPPoE client (adsl-modem in my case) recive an IP-address (real IP assigned by ISP) from the Radius server. The Client works well, the laptop attached to the adsl-modem have an access to the Internet. But I can't ping the client by its IP-address. There is no any firewall.

!

ip vrf EXTern

rd 100:1

!

subscriber profile EXTern-PROFILE

service local

pppoe service EXTern-PROFILE

!

vpdn enable

!

vpdn-group EXTern-PPPOE

! Default L2TP VPDN group

accept-dialin

protocol pppoe

virtual-template 1

l2tp tunnel receive-window 1024

!

bba-group pppoe global

virtual-template 1

service profile EXTern-PROFILE

ac name BGRD-GW1

!

interface GigabitEthernet0/0

description -= Internet =-

ip vrf forwarding EXTern

ip address 212.xxx.xxx.2 255.255.255.0

!

interface GigabitEthernet0/1

description -= DSLAM =-

no ip address

pppoe enable group global

!

interface Virtual-Template1

ip vrf forwarding EXTern

ip unnumbered GigabitEthernet0/0

ip virtual-reassembly

peer default ip address pool EXTern

ppp authentication chap

!

ip route vrf EXTern 0.0.0.0 0.0.0.0 212.xxx.xxx.1

!

2 REPLIES
New Member

Re: I can not reach a PPPoE client from the outside

LenWG#show int Virtual-aCCess 2

Virtual-Access2 is up, line protocol is up

...

Encapsulation PPP, LCP Closed

Base PPPoE vaccess

...

LenWG#show ip route vrf EXTern

Routing Table: EXTern

Gateway of last resort is 212.xxx.xxx.1 to network 0.0.0.0

C 212.xxx.xxx.0/24 is directly connected, GigabitEthernet0/0

212.yyy.yyy.0/32 is subnetted, 1 subnets

C 212.yyy.yyy.yyy is directly connected, Virtual-Access2.1

S* 0.0.0.0/0 [1/0] via 212.xxx.xxx.1

Where 212.yyy.yyy.yyy is the clients IP-address.

New Member

Re: I can not reach a PPPoE client from the outside

debug ip packet

LenWG#ping vrf EXTern 212.yyy.yyy.yyy

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 212.yyy.yyy.yyy, timeout is 2 seconds:

*May 19 06:01:14.320: IP: tableid=1, s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), routed via FIB

*May 19 06:01:14.320: IP: s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), len 100, sending

*May 19 06:01:14.320: IP: tableid=1, s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), routed via FIB

*May 19 06:01:14.320: IP: s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), len 100, sending

*May 19 06:01:14.320: IP: tableid=1, s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), routed via FIB

*May 19 06:01:14.320: IP: s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), len 100, sending

*May 19 06:01:14.320: IP: tableid=1, s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), routed via FIB

*May 19 06:01:14.320: IP: s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), len 100, sending

*May 19 06:01:14.320: IP: tableid=1, s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), routed via FIB

*May 19 06:01:14.320: IP: s=212.xxx.xxx.1 (local), d=212.yyy.yyy.yyy (Virtual-Access2.1), len 100, sending

Success rate is 0 percent (0/5)

299
Views
0
Helpful
2
Replies