Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

I Change component in ROMMON, and I no longer could enter the ROMMON Mode any suggestion

    I upgrade to a Flash 32mbs memory stick, as I reboot the 2600 Cisco router,  it appear in the ROMMON  mode,

nonetheless,  I followed some wrong procedure by changing components on the ROMMON command line illustrated below,

however now the router  reboot or start with symbol only V2V2v2a, and I can no longer enter the ROMMON Mode or key

anything in.

Any suggestion on how I could repair this problem????? I have a copy of the IOS on my TFTP server.

The following display shows an example of the confreg command I perform

rommon 7> confreg    

Configuration Summary

enabled are: break/abort has effect console baud: 9600 boot:

the ROM Monitor do you wish to change the configuration? y/n  [n]:  y

enable  "diagnostic mode"? y/n  [n]:  y

enable  "use net in IP bcast address"? y/n  [n]: y

disable  "load rom after netboot fails"? y/n  [n]:y

disable  "use all zero broadcast"? y/n  [n]: y

disable "break/abort has effect"? y/n  [n]: y

enable  "ignore system config info"? y/n  [n]: y

change console baud rate? y/n  [n]: y

enter rate: 0 = 9600,  1 = 4800,  2 = 1200,  3 = 2400            

4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200  [0]:  7

change the boot characteristics? y/n  [n]:  y

enter to boot: 0 = ROM Monitor 1 = the boot helper image 2-15 = boot system     [0]:  2

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

I Change component in ROMMON, and I no longer could enter the RO

Hello,

I see you changed the baud rate of rommon to 115200:

 

change console baud rate? y/n  [n]: y

enter rate: 0 = 9600,  1 = 4800,  2 = 1200,  3 = 2400            

4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200  [0]:  7

Are you now consoling with correct baud rate set on your terminal application? Can you try changing that?

Nik

3 REPLIES
Cisco Employee

I Change component in ROMMON, and I no longer could enter the RO

Hello,

I see you changed the baud rate of rommon to 115200:

 

change console baud rate? y/n  [n]: y

enter rate: 0 = 9600,  1 = 4800,  2 = 1200,  3 = 2400            

4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200  [0]:  7

Are you now consoling with correct baud rate set on your terminal application? Can you try changing that?

Nik

New Member

Re: I Change component in ROMMON, and I no longer could enter th

     Within the hyper terminal, I set the port setting to 9600 bit, however I can’t key anything within the console command line.  Any suggestion on how to get around this problem and change baud rate, if not through the hyper terminal?

Yes Nik, I Change the hyper terminal to 115200 bit ps and everthing work.

Thank You !!!!

Jesse R

Cisco Employee

Re: I Change component in ROMMON, and I no longer could enter th

No probs, Glad it helped.

Nik

1144
Views
0
Helpful
3
Replies