Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Cisco Employee

Input and CRC errors but no controller errors?

Hello,

I am working on an issue where I see errors on the interface...

Serial0/1/1:0 is up, line protocol is up

  Hardware is GT96K Serial

  Description: Connection to TP Provider

  MTU 1500 bytes, BW 1984 Kbit/sec, DLY 20000 usec,

     reliability 255/255, txload 122/255, rxload 118/255

  Encapsulation PPP, LCP Open, multilink Open

  Link is a member of Multilink bundle Multilink1, loopback not set

  Keepalive set (10 sec)

  Last input 00:00:00, output 00:00:00, output hang never

  Last clearing of "show interface" counters 1w0d

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: weighted fair  [suspended, using FIFO]

  FIFO output queue 0/40, 0 drops

  5 minute input rate 923000 bits/sec, 229 packets/sec

  5 minute output rate 955000 bits/sec, 173 packets/sec

     7324391 packets input, 3315314073 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     26446 input errors, 14140 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

But no errors are present on the controller...

Total Data (last 24 hours)

     0 Line Code Violations, 0 Path Code Violations,

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Could this be a problem with the multi-link config?

Thanks!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: Input and CRC errors but no controller errors?

Hello Cventici,

>> 20610 lost fragments, 3927978 reordered

    15227/8902947 discarded fragments/bytes, 0 lost received

    0x3D1F6D received sequence, 0xC032F9 sent sequence

as you can see there are 20610 lost fragments and 15227 discarded fragments and this is roughly similar to physical interface error counters

>> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     26446 input errors, 14140 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

Hope to help

Giuseppe

4 REPLIES
Hall of Fame Super Silver

Re: Input and CRC errors but no controller errors?

Hello Cventici,

you can use show ppp multilink to check ML PPP errors

Hope to help

Giuseppe

Cisco Employee

Re: Input and CRC errors but no controller errors?

rtr03>sh ppp multilink

Multilink1

  Bundle name: xxxxxxxx

  Remote Endpoint Discriminator: [4] xxxxxxxx

  Local Endpoint Discriminator: [1] xxxxxxxx

  Bundle up for 1w5d, total bandwidth 3968, load 1/255

  Receive buffer limit 24000 bytes, frag timeout 1000 ms

    0/0 fragments/bytes in reassembly list

    20610 lost fragments, 3927978 reordered

    15227/8902947 discarded fragments/bytes, 0 lost received

    0x3D1F6D received sequence, 0xC032F9 sent sequence

  Member links: 2 active, 0 inactive (max not set, min 1)

    Se0/1/0:0, since 1w5d

    Se0/1/1:0, since 1w5d

No inactive multilink interfaces

rtr03>

Hall of Fame Super Silver

Re: Input and CRC errors but no controller errors?

Hello Cventici,

>> 20610 lost fragments, 3927978 reordered

    15227/8902947 discarded fragments/bytes, 0 lost received

    0x3D1F6D received sequence, 0xC032F9 sent sequence

as you can see there are 20610 lost fragments and 15227 discarded fragments and this is roughly similar to physical interface error counters

>> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     26446 input errors, 14140 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

Hope to help

Giuseppe

Cisco Employee

Re: Input and CRC errors but no controller errors?

Thank you for pointing that out, I have opened up a ticket with our provider to review our multi-link config.

Have a good day!

500
Views
0
Helpful
4
Replies
CreatePlease login to create content