Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Installing 2nd WIC card in Cisco 2811 router

Hello,

I'd like to know the proper procedure for installation, please. Does it require the router to be powered off? Any help would be appreciated.

Best regards.

lf

8 REPLIES
Bronze

Re: Installing 2nd WIC card in Cisco 2811 router

Bronze

Re: Installing 2nd WIC card in Cisco 2811 router

here is a short step:

1. issue the "sh diag" to verify the slot

2. configure card type "card type t1 slot# where slot# is the one return from sh diag.

regards,

New Member

Re: Installing 2nd WIC card in Cisco 2811 router

Thank you your help...I can't use "card" command though, not sure if it's because of IOS ver?:

Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 28-Nov-07 21:09 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

Router uptime is 19 weeks, 1 day, 2 hours, 59 minutes

System returned to ROM by power-on

System image file is "flash:c2800nm-ipbase-mz.124-3i.bin"

Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.

Processor board ID FTX1234A0QF

2 FastEthernet interfaces

1 Serial interface

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Is it necessary to use this command?

thanks

Hall of Fame Super Gold

Re: Installing 2nd WIC card in Cisco 2811 router

Only for T1/E1 cards.

Bronze

Re: Installing 2nd WIC card in Cisco 2811 router

I am not sure but it should work with ver 12.4

Are you issuing the command from the config mode? what do you get from sh diag?

New Member

Re: Installing 2nd WIC card in Cisco 2811 router

I have not installed 2nd WIC card yet; I have WIC-1DSU-T1-V2 card already installed in WIC slot 0, for the existing T1 line.Still I can't use "card" command, so I'm afraid that I will not be able to make proper configuration for additional T1 line..

sh diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : FOC12323XKT

Hardware Revision : 1.0

Top Assy. Part Number : 800-26920-04

Board Revision : A0

Deviation Number : 0

Fab Version : 04

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20080809

Chassis Serial Number : FTX1234A0QF

Chassis MAC Address : 0022.904d.8088

MAC Address block size : 24

CLEI Code : COM7R00ARA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-05

Version Identifier : V05

--More-- EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 31 32 33 32 33 58 4B 54 40

0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30

0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 32 68 A9 C2 8B 46 54 58 31 32 33 34

0x40: 41 30 51 46 C3 06 00 22 90 4D 80 88 43 00 18 C6

0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF

WIC Slot 0:

FT1 PMC4351

Hardware Revision : 1.2

PCB Serial Number : FOC122941SD

Part Number : 73-8346-05

Board Revision : A0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0-0

Product (FRU) Number : WIC-1DSU-T1-V2

Top Assy. Part Number : 800-22193-03

CLEI Code : IPUIAPRRAA

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 32 32

0x10: 39 34 31 53 44 82 49 20 9A 05 42 41 30 03 00 81

0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 57 49 43

0x30: 2D 31 44 53 55 2D 54 31 2D 56 32 20 20 20 20 20

0x40: 20 C0 46 03 20 00 56 B1 03 C6 8A 49 50 55 49 41

0x50: 50 52 52 41 41 FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Hall of Fame Super Gold

Re: Installing 2nd WIC card in Cisco 2811 router

That is a T1 only card and you don't need to enter card type command

New Member

Re: Installing 2nd WIC card in Cisco 2811 router

Thank you to all who responded to my question.

Regards,

lf

2503
Views
0
Helpful
8
Replies