Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

Dear Team,

We have Cisco2621XM router,  where in the below IP SLA is not supporting. Refering the Cisco feature navigator, understood that the below features will support c2600-ik9s-mz.122-46a.bin. But i am not able to execute IP SLA command in config mode.

The below are the features captured from Cisco feature navigator and the same are not supporting in c2600-ik9s-mz.122-46a.bin IOS.

IP SLAs - DHCP Operation
IP SLAs - Distribution of Statistics
IP SLAs - DLSW+ Operation
IP SLAs - DNS Operation
IP SLAs - FTP Operation
IP SLAs - History Statistics
IP SLAs - HTTP Operation
IP SLAs - ICMP Echo Operation
IP SLAs - ICMP Path Echo Operation
IP SLAs - One Way Measurement
IP SLAs - Reaction Threshold
IP SLAs - Scheduler
IP SLAs - SNA LU2 Echo
IP SLAs - SNMP Support
IP SLAs - TCP Connect Operation
IP SLAs - UDP Echo Operation
IP SLAs - UDP Jitter Operation

1 ACCEPTED SOLUTION

Accepted Solutions

Re: IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

I've chosen the same features for IP SLA with Features Navigator and the lowest IOS version that support what you need it's 12.3, Enterprise features set.

See attachement.

I have here a 2600 with c2600-i-mz.123-1.bin, and:

(config)#rtr ?
  <1-2147483647>          Entry Number
  key-chain               Use MD5 authentication for RTR control message
  low-memory              Configure low water memory mark
  reaction-configuration  RTR Reaction Configuration
  reaction-trigger        RTR trigger assignment
  reset                   RTR Reset
  responder               Enable RTR Responder
  restart                 Restart an active entry
  schedule                RTR Entry Scheduling
  slm                     Service Level Management

I think you have to upgrade.

Calin

4 REPLIES

Re: IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

Does it work with rtr command instead of ip sla ?

Cheers,

Calin

New Member

Re: IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

Hi Calin,

No, None of the commands are working. I have attatched the o/p.

Thanks,

Sigeesh

Re: IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

I've chosen the same features for IP SLA with Features Navigator and the lowest IOS version that support what you need it's 12.3, Enterprise features set.

See attachement.

I have here a 2600 with c2600-i-mz.123-1.bin, and:

(config)#rtr ?
  <1-2147483647>          Entry Number
  key-chain               Use MD5 authentication for RTR control message
  low-memory              Configure low water memory mark
  reaction-configuration  RTR Reaction Configuration
  reaction-trigger        RTR trigger assignment
  reset                   RTR Reset
  responder               Enable RTR Responder
  restart                 Restart an active entry
  schedule                RTR Entry Scheduling
  slm                     Service Level Management

I think you have to upgrade.

Calin

New Member

Re: IP SLA IS NOT WORKING IN c2600-ik9s-mz.122-46a.bin.

Hi Calin ,

The configuration is fine after IOS upgrade. Thanks for your inputs.

1710
Views
0
Helpful
4
Replies