12-01-2013 03:15 AM - edited 03-04-2019 09:44 PM
Hello Experts ,
my issue in ISDN-PRI leased line i used for remote data users to access my local network ,
i have a router with HWIC-2CE1T1-PRI and connected to ISDN PRI 30 channels E1 , it configured with local database of usernames and passwords , all remote users with ISDN BRI can call ISDN PRI number and access local network after authtaction , but i have an issue when users call from analog land line they cannot access and will rject call ! ISP said that PRI is configured from its side to received both digital (ISDN BRI) and analog(Land line) calls.
i need to know what the equipment must install in router like PVDM2 or PVDM3 and what the missed configuration
this is the running configuration below :
hostname PRI-E1
!
card type e1 1s
!
aaa new-model
!
aaa authentication login default local none
aaa authentication ppp default local
isdn switch-type primary-net5
!
interface FastEthernet0/0
ip address 192.168.1.1 255.255.255.0
no shut
!
controller e1 1/0
framing crc4
linecode hdb3
clock source line
line-termination 75-ohm
pri-group timeslots 1-30
no shut
!
interface Serial1/0:15
description PRI D Channel CktA
ip unnumbered FastEthernet0/0
no ip redirects
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem
fair-queue
no cdp enable
ppp authentication chap defulaet
ppp multilink
!
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
ip tcp header-compression
dialer in-band
dialer idle-timeout 255 either
dialer-group 1
async mode interactiv
ppp authentication chap defuleat
ppp multilink
group-range (0/322 0/357)
!
ip default-gateway 192.168.1.1
ip route 0.0.0.0 0.0.0.0 192.168.1.1
!
dialer-list 1 protocol ip permit
!
!
line aux 0
session-timeout 35790 output
modem InOut
modem autoconfigure discovery
transport input all
autoselect during-login
autoselect ppp
autoselect timeout 120
speed 57600
!
line con 0
password cisco
logine
!
username ahmad
password Cisco321
!
line (0/322 0/357)
login local
modem InOut
modem autoconfigure discovery
transport input all
autoselect during-login
autoselect ppp
line vty 0 4
password cisco
login
transport input telnet
12-01-2013 05:50 AM
I found this example of configuring PRI to handle analog calls. It talks about the requirement to have internal digital modems. Perhaps this is your issue?
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_configuration_example09186a0080094557.shtml
I hope this link will be helpful.
HTH
Rick
12-01-2013 06:07 AM
Yes, this informative. But I still did not know if will work with me!!
I have Cisco 2911 router with HWIC-2CE1T1-PRI and PVDM v2
This will accept analog calls?
12-01-2013 06:30 AM
This link
http://www.cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88.html
certainly seems to indicate that your 2911 supports the card and should work with PVDMv2
Interoperable with Cisco digital modem modules PVDM2-12DM, PVDM2-24DM, and PVDM2-36DM (HWIC-1CE1T1-PRI and HWIC-2CE1T1-PRI modules only)
HTH
Rick
12-01-2013 06:58 AM
Ok, understood 2911 support card and PVDM, but my point is:
HWIC-2CE1T1-PRI With PVDMv2 will accept incoming analge calls?
Thank you
12-01-2013 05:58 PM
I wish I had an authoritative answer to that question. But I do not. Perhaps some other participant in the forum can offer an answer to this.
HTH
Rick
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: